RAS used machine for sale

sheet width: 2540 mm plate thickness: 2 mm strokes per minute until: 63 throat: 100 mm cutting angle: 1,13 ° table height: 750 mm table width: 320 mm table height over floor: 750 mm total power requirement: 3 kW weight of the machine ca.: 1600 kg dimensions of the machine ca.: 3,1 x 2 x 1,3 m Electric 380 Volt: Rear register front operated: 15 - 550 Foot switch: Squaring arm: Support arms: 3 x Motorized guillotine shears in the swing cutting system with adjustable from the front manual backgauge with analogue display and reading optics. Power transmission via gearbox, eccentric shaft and connecting rod on the cutter bar. Less noise level because the gear is only switched on during the cutting process is. Hold-down beam with continuous pressure element made of elastomers material that ensures secure clamping of the sheet metal. The cutting performance refers to 400 N/mm² strength. Ma ...

sheet width: 2040 mm plate thickness: 3.0 mm thickness at Niro-steel: 1.5 mm no. of strokes: 50 Hub/min cutting angle: 1.4 Grad table height: 750 mm distance between columns: 2120 mm back stop - adjustable: 1.0 - 550 mm column arm: 100 mm Control: manuell engine output: 5.5 kW weight of the machine ca.: 2050 kg. range L-W-H: 2600 x 1980 x 1400 mm Furnishing: - robust / motorized swing-cut guillotine shears - Shatterproof, torsion-free steel welded construction - compact and clear mechanical design - manual backgauge, with analogue position display adjustable from the front Continuous adjustment over the entire travel range Adjustment range 1.0 - 550 mm - Machine side stand with projection .. 100 mm - manual cutting gap adjustment - 1x hold-down bar - 1x long side stop - 2x support arms - 1x freely movable foot switch - rear sheet metal slide - 2x EMERGENCY stop buttons at the front -  ...

CNC-controlled edge bending machine, manufactured by RAS Germany-Reinhardt Maschinenebau GmbH type 64.12 - 1280 x 3.5 mm. Thickness of bent steel sheet (St40) 3.5 mm; bending length 1280 mm. Setting the bending angle up to 28 degrees from the desktop. Jaw opening 300 mm. 2.2 kW drive. Weight 1180 kg. Full DTR documentation. Lots of additional tools, strips for flattening sheet metal.

Edge bending machine manufactured by RAS GmbH Germany -type 74.40 4060 x 3 mm. Multibend 901 control, color, 2D graphics, bending simulation. Automatic setting of the bending radius depending on the material thickness. Super simple and intuitive control operation. Jaw opening 300 mm. Large bumper departure up to 1500 mm. 7.5 kW drives. Weight 6800 kg. Full O&M documentation, diagrams.

This RAS FLEXIbend 73.40 Bending machine was manufactured in the year 2005 in Germany. It is equipped with a SYSTEM 6000 TOUCH control unit. The machine has a bending length of 4060 mm.

This RAS 62.30 TURBObend Plus bending machine was made in the year 2004. It is equipped with a Ras CNC 6000 control unit. The machine has a sheet length of 2540 mm and a max. sheet thickness of 2 mm.

Ras FLEXIbend 73.30 Folding Machine Working length: 3200 mm Max thickness: 3 mm Working hour: 14.195 Upper Beam Stroke : 300 mm Machine is in excellent condition

We sell a rectangular air duct lock shaper. In good shape. Length 6000.0 Width 1000.0 Height 1500.0 Weight 1000.0 Advanced information Working length 2500.0 Max thickness 1.0 Motor power 3.0

sheet width: 1040 mm plate thickness: 2,50 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 0,750 t dimensions of the machine ca.: m Manual back gauge can be operated from the front up to 500 mm Side stop Knife sharpened The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3200 mm plate thickness: 2,50 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 3,80 t dimensions of the machine ca.: m Segmented upper beam rail Manual and automatic bending mode possible Bending angle adjustment via potentiometer The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3190 mm plate thickness: 6 mm distance between columns: 3250 mm cutting angle: 1,2 ° no. of strokes: 32-75 Hub/min column arm: 100 mm back stop - adjustable: 5-1000 mm table height: 800 mm oil volume: 150 l total power requirement: 15 kW weight of the machine ca.: 6200 kg dimensions of the machine ca.: 3500x2000x2000 mm The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 4000 mm plate thickness: 2,5 mm distance between columns: 4060 mm Control: total power requirement: 3 kW weight of the machine ca.: 5,5 t dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3100 mm plate thickness: 4,00 mm distance between columns: mm total power requirement: 7,50 kW weight of the machine ca.: 4,20 t dimensions of the machine ca.: m - CNC controlled back gauge 10 – 1000mm - central cutting gap adjustment - Pneumatic sheet metal support - Angle stop 2500 mm - 3 support arms The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Bending tool, die, upper knife, upper tool, straight tool, die tool, seam closing tool -Tool: for folding machine RAS Typ 74.30 -Dimensions: see the drawing in the photos -Distance recess rail: center center 650 mm -Dimension: 3060/28/H121 mm -Weight: 65kg

Guillotine shears, plate shears, plate shears, crank guillotine shears -Mechanical guillotine shears -Cutting width: 2040 mm -Max. Cutting thickness: 2.0 mm -Rear stop -Installation dimensions: 2650/1900/H1070 mm -Transport dimensions: 2650/730/H1070 mm -Weight: 1378 kg

Swivel bending machine, edge bench, gutters, roof gutters, beading machine, beading machine -Max. Working width: 1280 mm -Max. Sheet thickness: 1.75 mm -Opening width: 180 mm -Clamping via: threaded spindle -Bending angle adjustable via: stop -Dimensions: 1850/600/H1240 mm -Weight: 380 kg

model RAS 62.25 turbobend plus cnc control system 5000 year of manufacture 2002 max. sheet length 2540mm sheet thickness up to 2.25 mm rear bumper electrically extendable up to 1550mm weight 2500 kg very good condition, the machine is overhauled and oil changed

sheet width: 2040 mm plate thickness: 2,00 mm distance between columns: mm total power requirement: kW weight of the machine ca.: 1,10 t dimensions of the machine ca.: m Manual back gauge adjustable from the front up to 550 mm Pneumatic sheet metal support The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3190 mm plate thickness: 6,3 mm distance between columns: 3200 mm Rear feed width: 5-1000 mm strokes per minute: 30 - 50 cutting angle: 1,2 ° control: RAS System 2005 total power requirement: kW weight of the machine ca.: t dimensions of the machine ca.: 3,83 x3,82 m Equipment / Accessories: - small parts diverter - automatic cutting gap adjustment - scrap separation - return-to-sender - cutting technology: swing cut - documentation The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 3200 mm plate thickness: 4 mm distance between columns: mm pressure: t chamfer lenght: mm total power requirement: kW weight of the machine ca.: 6000 kg dimensions of the machine ca.: m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

working width: 2040 mm plate thickness: 3,5 mm distance between columns: 2100 mm sheet width: 2040 mm output: 3,7 kw weight of the machine ca.: 2,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Ras 1020 x 2 mm Worklength: 1050 mm Sheetthickness: 2 mm Length: 2000 mm Width: 1060 mm Hight: 550 mm Weight: 444 kg

max thickness: 3 mm roller dia: 94 mm speed: 4m/min min bendradius for 90° elbow: - thickness 0,5 gt; 1,5 mm = radius 100 - thickness 1,5 gt; 2,25 mm = radius 150 - thickness 2,25 gt; 3 mm = radius 200 min bendradius for 180° elbow and ring: - thickness 0,5 gt; 1,5 mm = radius 150 - thickness 1,5 gt; 2,25 mm = radius 300 - thickness 2,25 gt; 3 mm = radius 450 power: 2 kW weight: 270 kg

Thenbsp;Ras ductseamer 22.82 produces longitudinal seams along the edges of square or rectangular cross-section ducts. This duct seaming machine has 15 roller shafts which are equipped with seaming rollers, and nine further intermediate rollers are located in an overhead seaming bar. The RAS 22.82 is a very simple and reliable machine that can be easily operated by one person. max thickness: 1,25 mm

sheet width: 2000 mm plate thickness: 2 mm distance between columns: 2040 mm total power requirement: 0 kW weight of the machine ca.: 1,2 t dimensions of the machine ca.: 2,5x0,64x1,4 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 2000 mm plate thickness: 2,25 mm distance between columns: 2040 mm total power requirement: 7,5 kW weight of the machine ca.: 1,5 t dimensions of the machine ca.: 2,2x1,7x1,1 m The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Type: 74.40 CNC folding beam adjustment: 80 mm CNC pivot joint adjustment: 80 mm Max worklength: 4060 mm Max tickness: 3 mm Distance between clampblock -- ram: 400 mm Max displacement back gauge: 1550 mm

Mot. Beading machine make RAS type 12.30Masch. -No: 246/9 built in 1973Roller center distance: 68 mmMax. Sheet thickness at 40 kg strength: 1.75 mmMax. working depth: 250 mmWorking speed: 8.8 m / minDrive power: 0.55 kWDimensions L x W x H: 520 x 700 x 1350 mmWeight approx: 200 kgWith- pneum. Delivery of the harmonic- Footswitchused, ready for operationPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Manual beading machine make RAS type 11.11Fabr. -No: 39/9 built in 1984Max. Sheet thickness: 1.25 mmRoller center distance: 50 mmOutreach: 200 mmWeight approx: 16 kgOutside dimensions approx: 500 x 250 x 400 mmWith- 8 sets of rolls- Underframeused, in good conditionPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools

Beading machine make RAS type 110 MMachine -No: 69/6 built in 1956Technical specifications:Max. sheet thickness: 1.75 mmmaximum projection: 250 mmDrive power: 0.75 kWWith- foot pedalusedPrice on request.Delivery: ex warehouse or location free loading truck.Payment: net at takeover or by appointment.Technical data are not binding. Errors excepted.We would be pleased, if you like our offer and are always available for your queries.Best regardsM. WaldeckWAHO Machine Tools