planing machines used for sale

WEINIG high performance planer Type Hydromat 22 BL (full checked!) Built in 1995 With safety hood and soundproofing cabin! Machine specifications: - Planing capacity 220 x 120 mm - Feeding, 8- 80 m/min, motor 18.5 kW Spindle layout: Bottom-right-Links Top - bottom, table rigid Bottom, table rigid, spindle prepared Top - bottom, table rigid, spindle prepared gap unit, consisting of 1 right and 1 left spindle 30 kW each (4500 rpm) incl. table roll, sliding roller, spray indentation and wedge dissipation 4 Roller pull-out Special printing and fittings for the production of top layer slats Feed (divider) for slats and pull-out tape

Working width: 318 / 295 mmWorking height: 170 mmMotor output: 2,25 kWLength of the planing table: 1300 mmNumber of knives: 3 St.Feed speed: 5,3 m/min.Dust suction hood: 100 mmconnected load frequency: 400 Vmachine weight ab.: 160 kgDimensions (L/W/H): 1150 x 530 x 930 mmThe planer and thicknesser is delivered almost fully assembled.For thickness planing, the same connection is used for suction as for surface planingused. However, this is placed upwards over the storage table. The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Koelle Edge Planer Model FKF 51 Built in 1993 max material thickness 45 mm, Machine size L 304 x W 65 x H 87 cm, Joining head with carbide reversible knife mobile Weight approx. 360 kg The machine is in good condition, ready for use. Subject to changes, errors, prior sale ! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system+technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Phone: 0041 62 966 18 32 Fax 0041 62 966 21 12

x-travel: 11000 mmy-travel: 2.500 mmworkpiece height: mmtable width: mmtable length: mmweight of the machine ca.: tdimensions of the machine ca.: mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Koelle edge planing machine model FKF 51 is in good condition, ready to use. L x W x H = 3000 mm x 700 mm x 950 mm Weight approx. 200 kg Built in 1982 Engine No. 390 The rubber rings at the pressure rollers should be times replaced. Subject to changes, errors, prior sale! Service/spare parts by MATEC CH-4900 Langenthal/DE-79618 Rheinfelden MATEC system + technik GmbH Mechanical engineering Eisenbahnstrasse 25 CH-4900 Langenthal/Switzerland Tel. 0041 62 966 18 32 Fax 0041 62 966 21 12

x-travel: 8000 mmy-travel: 2.500 mmworkpiece height: 2.360 mmtable width: 2.240 mmtable length: 10.100 mmweight of the machine ca.: tdimensions of the machine ca.: 20,0 x 8,5 x 5,2 mThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Weinig Profimat 23 Fortec + EM11 four-sided planer Working width 230mm Working height 140mm Number of spindles 6 Spindle arrangement Bottom 7.5kw Rights Left 11kw Top 7.5kw Top 5.5kw Bottom 5.5kw Pneumatic clamps Feed speed adjustable on the variator Drive on cardan shafts CE Certified EM11 Hydraulic Component Feeder Possibility to purchase the machine without a feeder

Working width: 410 mmLength of the planing table: 2.200 mmNumber of knives: 5 St.Motor output: 5 kWweight of the machine ca.: ca. 411 kg: Tersa : Ja Dust suction hood: 120 mmturning speeds: 5.000 U/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 7406 Type: RISZ 16 Producer: ARTHUR KLINK Created: 1993 Parameters: Theoretical diameter of the tool: 95 mm Max. workpiece height: 300 mm Clamping surface: 400x400 mm Maximum working stroke: 1250 mm Maximum stretching force: 16 t Weight: 6900 kg

Working width: 410 mmNumber of knives: 2 St.Motor output: 4 kW: Streifenhobelmesser turning speeds: 4.600 U/min: Nein The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Inv. Num. : 6696 Type: Profiset 60 Producer: SCM Created: 2018 Parameters: Number of spindles: 5 Vacuum belt width: 25-230 mm Working height: 6-120 mm Max. speed: 6000 1/min Equipment: Swivel head

Working width: 530 mmLength of the planing table: 2.900 mmNumber of knives: 4 St.Motor output: 4 kWweight of the machine ca.: 850 kg: Tersa : Ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Used four-sided planer Int. Art. Ref. m3491 Manufacturer: SCM Type P 64 B Built in 1988 4 planer shafts YOC 1988 max. planing width 165 mm min. planing width 23 mm max. planing height 105 mm min. planing height 6 mm Spindle speed 6,000 rpm. Weight approx. 950 kg Location: 59425 Unna The machine can be viewed under electricity. We will be happy to send you more photos by e-mail. A forklift for loading is available. We reserve the right to sell in advance. It is possible to expertly inspect the items for sale on site. Specific questions should be clarified in advance. The information, such as technical data, dimensions, year of construction, condition are non-binding and have been shown to the best of our knowledge and belief. Errors are therefore reserved. The warranty/guarantee is excluded. The goods are sold from the location / warehouse, with the transfe ...

Working width: 410 mmLength of the planing table: 2.600 mmNumber of knives: 4 St.Motor output: 4 kWDimensions (L/W/H): 2.600 x 1.400 x 1.200 mmweight of the machine ca.: 561 kg: Tersa : Ja The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

MARTIN T90 Year of construction 1996 Nominal current: 64 A max. planing width: 260 mm max. planing height: 160 mm 5 spindles: 4x Tersa planer head + 1x universal spindle Spindle arrangement: Bottom – Right – Left – Top – Universal Spindle 1 – 4: 4 knife shaft – Tersa Use of profile knives for chamfers and radii possible (spindle R + L + O) Spindle 5: Universal 40 mm spindle (max. tool diameter: 220 mm) swivel (- 45° / + 90°) Bottom: 5.5 kW Left+Right: 5.5 kW Top: 5.5 kW Universal: 7.5 kW Feed speed: 4 – 25 m/min. (infinitely variable) electronic positioning control (storage of up to 100 pairs of dimensions possible) Engine brake Central lubrication Extras: Universal spindle Table extension at the spout Hold-down device for joining shaft right incl. 8 new rubber pull-out rollers Suction connection: 250 + 160 mm Dimensions: L: 524.5 cm W: ...

Working width: 520 mmWorking height: 240 mmMotor output: 7 kWNumber of knives: 4 St.Feed speed: 5/8/12/16 m/min.weight of the machine ca.: ca. 500 kg: Tersa : Ja Dust suction hood: 120 mmThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Key data: 510 mm, 2450 mm, 2 St.

Gebr. Planer REX A510 YOC 1981 Motor power: 4 kW Planing width: 51 cm Table length: 245 cm 2-Knife Shaft Strip Plane Knife Working height: 100 mm Additional overarching fence (standard dressing fence) incl. 2 rollers Feeder Wood Type ETK 0.3 / 0.5 HP Aigner Relief Stop Weight: approx. 950 kg Sold in ACTUAL condition and unrefurbished from carpentry dissolution. Fixed price.

Working width: 510 mmLength of the planing table: 2.250 mmNumber of knives: 4 St.Motor output: 5,5 kWDimensions (L/W/H): 2.427 x 1.340 x 890 mm: Ja weight: 750 kgDust suction hood: 140 mm: Keilleistenmesser The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

SCM 2250 Dressing thickness planer Motor 5.5kW Planing width 500mm 4-planer blade shaft Dressing table length 2200mm Built in 1981 Thickness height 225mm 1 under-table roller G&2978-M3ZNB

Working width: 520 mmWorking height: 300 / 3,5 mmMotor output: 7 kWNumber of knives: 4 St.Feed speed: 5/8/12/18 m/min.weight of the machine ca.: 680 kgDust suction hood: 150 mm: Tersa turning speeds: 4.500 U/minThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Four-side planer / profile milling machine Fabr. Gubisc Model: 172/1K+R Year of construction: 1981 Planer width: 170mm 5 spindles

x-travel: NA mmy-travel: NA mmworkpiece height: mmstroke length max.: 450 mmtable length: 450 mmtable width: 350 mmtotal power requirement: 1,7 kWweight of the machine ca.: tdimensions of the machine ca.: mShaper, horizontal,mechanic,vice hydraulic The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Four-sided planing and roll forming machine SCM COMPACT P max. working width ( finished dimension ) 230 mm max. working height ( finished size ) 120 mm Motor power dressing spindle 4 kW Motor power vertical spindles 5.5 kW Motor power upper horizontal spindle 4 kW Profile depth 20 mm Infeed table length 2500 mm Motorized height adjustment of the feed system Feed element before dressing Positioning of the working units: The working units are adjusted at the front of the machine with a mechanical digital display of the position Manual pump for lubrication of the work table Machine is WORKSHOP OVERHAULED IN TOP CONDITION 1 set of planing tools for FREE

Number of spindles: 6 St.Working width: 230 mmWorking height: 120 mmLength of the planing table: 2500 mmFeed motor: 4 kWFeed speed: 5-30 m/min.Control: Weinig PowerCom Weinig Powermat 500 for window production---------------------------------------------Machine will be checked at our warehouseShort summary:---------------------------------------------6 Spindles with 8,000 rpm and 7.5 KW5 x HSK/PowerlockWindow package with glazing bead separationSpindles axially and radially CNC controlledright and upper spindles with common pneumatic timing forGlazing bead cuttingLarge control Powercom with touchscreenDetailed description:---------------------------------------------Tool arrangement No. 018 for window productionTechnical specifications:---------------------------------------------Working width 20 - 230 mm (at tool cutting circle 93 - 125 mm)Working height 8 - 120 mm (at tool cutting circ ...

SCM Sintex XL four-sided planer Working width min/max: 23-180mm Working height min/max 6-105 Number of spindles 4 Spindle system: Bottom Right 7.5kw Left Top 5.5kw Minimum workpiece length 300mm Two-stage feed speed 6-12m/min Spindle diameter 30mm Spindle speed 6000 r.p.m CE Certified Input table length 1700mm

Number of spindles: 6 St.Working width: 240 mmWorking height: 120 mmDimensions (L/W/H): 4900 x 1700 x 1700 mmweight of the machine ca.: 3500 kgControl: CNC SCM SUPERSET NTE 31 PLUS automatic profile milling machine with 6 shafts14 axis control with touch screen - WINDOW VERSIONMachine with 6 spindlesSpindle speed 8,300 rpmWorking width 240 mm, working height 120 mmElectronic horizontal and vertical positioning of the spindlesGlazing bead cuttingTouchscreen controlsDetailed technical description, seeadjacent PDF documents.Suction nozzle diameter:1. Spindle down: 120mm2nd spindle right: 120 mm3. Left spindle: 120 mm4. Spindle top: 150mm5. Spindle top: 150mm6. Spindle below: 120mmOption: workpiece return to the operatorImages are from our archive of a machine of the same model.(Technical information according to the manufacturer - without guarantee!)The data for this ad was created with Mod ...

Code: 0310 Brand: PINHEIRO MAQUINAS - PORTUGAL Model: PMA2 - MS - 510 2- Shaft Planing Moulding machine with moving head and multi-blade shaft for sawmill, wooden beams, planks, wooden roofs - CE Standard Technical data: Sturdy construction Working width mm 0-510 Working height mm 12-260 Automatic lifting Max cutting width mm 490 Max cutting height mm 120 Max stock removal lower shaft mm 12 Max stock removal upper shaft mm 15 Minimum workpiece length mm 415 intermittent pieces Minimum workpiece length mm 180 continuous Variable feed speed m/min 7/40 with display Horizontal shaft speed rpm 5300 Multi-blade shaft speed rpm 2300 Multi-blade shaft diameter mm 75 Saw blade diameter mm 200-400 Backstop safety devices Pneumatic pressure system on n° 8 upper drive rollers N° 3 lower drive rollers - Diameter mm 112 N° 4 tersa knives for each shaft Motor power Lo ...

Number of spindles: 6 St.Working width: 230 mmWorking height: 120 mmLength of the planing table: 2500 mmFeed motor: 4 kWFeed speed: 5-30 m/min.Weinig Powermat 400 with HSK/Powerlock, axial/radial CNC controlled------------------------------------------------------------ -----------Short summary:-------------------------------------------------------------- ---------6 spindles with 8,000 rpm5 x HSK/PowerlockAxial and radial CNC adjustment of the spindles via controlCNC - controlled adjustment and positioning of the feedDetailed description:---------------------------------------------------------- -------------Technical specifications:Working width: 20-230 mmWorking height: 8-120 mmNumber of spindles: 61. Tool holder - below------------------------------------------------Motor with brake: 5.5 kWSpindle diameter: 40mmSpeed: 6,000 rpmTool flight circle: 93 - 160 mmAxial adjustment range: 5  ...

Key data: 530 mm

Surface planer, dressing machine Maka AH530 with Centrofix shaft Very robustly built machine Planing width max. 530mm max. chip removal 20mm Adjustment of the planing strength with handwheel Drive motor 4kW Automatic motor brake 4-knife shaft Centrofix (comparable to Tersa) with new knives Casting tables slit table lips Low-noise design Swivelling stop with fold-down auxiliary stop Oscillating knife protection Suction nozzle 140mm Original paint, only reworked in places V-belt renewed New knives Dimensions approx. 2900 x 900 x 1200mm (LxWxH). Weight approx. 850kg. The machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration in our warehouse, see "other offers of this supplier".

working length: 2000 mmWorking width: 250 mmWorking height: 970 mmWeinig pressure conveying system DEF 25 to the operator in workingheight for UnicontrolLength 2000 mmDepth 1800 mmBrand width 250 mmRear roller conveyor not driven 2500 mmRoll width 250 mm(technical details according to manufacturer - without guarantee.)The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.