used HOMAG kal

Single-sided edge banding machine Make: HOMAG Type: KAL 210 AMBITION 2264 Year of construction: 2014 One-sided edge banding machine for editing of straight workpiece edges and for gluing and post-processing in the longitudinal and transverse pass. Overview of aggregate equipment: - Separating agent spray unit - Joining milling unit - Gluing unit A20 with 2 rolls - end trimming unit HL84 - Pre-milling unit BF10 - Form milling unit FK11 manual - Profile scraper PN10 - Finishing unit Feed 18 - 25 m/min. Feed max. with FK11 20 m/min. Working height 950 mm Pneumatic connection 6 bar Total length 7845mm Workpiece thickness 8 - 60 mm Edge height max. = workpiece thickness + 4 mm Edge material roll 0.3 - 3 mm Edge material strips 0.4 - 20 mm Aggregate equipment: - Separating agent spray unit top/bottom - Joining milling unit 2 motors each 3 kW, 150 Hz ...

Description: Flexline HOMAG PROFI KAL 330/6/A3/S2 edge banding machine  , , , serial number: 0-200-24-9153 is equipped as follows:  , , , HOMAG PROFI TBL 100/35/12 feed table with fully automatic workpiece feeding system WZ10 for workpieces with different dimensions in longitudinal and transverse direction Technical data: - Workpiece length 250 - 2500 mm - Electro-pneumatically controlled cross weigher - Air cushion table ( is not included in the scope of delivery )  , , , 2 HOMAG PROFI KAL 330/6/A3/S2 edge banding machine Technical data: - Universal trimming unit UF11, electro-pneumatically controlled  ,Note: the feedback is not included in the scope of delivery  , serial number: 0-200-24-9153, workpiece thickness: max.60 mm, feed: 18-25 m/min, joint trimming unit: Ja/Yes, snipping unit: Ja/Yes, fine trimming unit: Ja/Yes, pro ...

Manufacturer: Homag, Type: KAL 310, Year: 2004, Control: NC 21, Software: Homag, Min-max edge material mm: 0,5-3, Min.-max. workpiece length in mm: 150-3000, Min.-max. workpiece height in mm: 10-55, Min-max feed m/min: 24, Axis control: yes, Premilling: yes, Fine milling: yes, Application of separation agent: yes, IR zone: yes, Power per lamp: 400 Watt, Coil magazine: einfach, Strip magazin: yes, Min.-max. batten magazine mm: yes, Mitre stations: yes, Bevel milling: yes, Radius milling axis adjustment: lyes, Corner tracing type: FK 11, 2 motors: 2, Radius scraper: yes , Scraper with axis adjustment: yes, Flat scraper: yes, Spraying system 2: yes, Cleaning nozzles: yes, Bonding part EVA: yes, Pre-smelting Kg/Hr: yes, Buffing unit: yes, Top pressure belt/roller: Band, Separation agent setup: yes, Workpiece support: yes, Machine lenght mm: ca.9,5, Noise enclosure: yes, Return type: Bargsted ...

Manufacturer: Homag , Type: KAL 310/8/A20/S2, Year: 2005, Control: PC 22, Work piece width min-max mm: min 55/100, Min.-max. workpiece height in mm: 12 - 60, Min-max feed m/min: 18 - 24, Einlauflineal gesteuert: yes, Premilling: 2 x 3kW, Application of separation agent: yes, Coil magazine: 2, Mitre stations: Fase / Gerade, Pre-milling: 2 x 1,5 kW, Bevel milling: FK 13 - 8Fach, radius milling: 4 kW, Corner tracing type: MN 21, Flat scraper: FA 11, Bonding part EVA: A 20, Top pressure belt/roller: Band, Work piece refeeding: vorinstalliert, FREE TEXT: Frreiplatz, Year :2005

Manufacturer: Homag , Type: KAL 310/7/A3/S2, Year: 2004, Control: NC21, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 55/100, Min.-max. workpiece height in mm: 12 - 60, Edgeband height max mm: 60, Min-max feed m/min: 10-30, Axis control: Verleimteil/Druckzone/Formfräsen, Servo Einschubtisch: yes, mit Vakuum: 2x 3Kw, Profile milling: yes, Machining cracks: yes, Power per lamp: 2 Rollen, Coil magazine: HL 84, Strip magazin: 2 X0,55 kW, Min.-max. batten magazine mm: 2 X 0,4 kW, Mitre stations: yes, Bevel milling: FK 11/Verstellung automatisch, radius milling: 0,55 kW, Vertical grooves: PN 20, Radius scraper: yes, Rolling chain: yes, Spraying system 2: yes, Ersatzverleimteil : 5, Edge sanding: Riemen, Edge sanding radius: yes, Free places: yes, Year :2004

Manufacturer: Homag, Type: KAL 310/7/A20/S3 , Year: 2011, Control: PC 22, Software: Windows XP/Woodscout, Barcode: möglich, Min-max edge material mm: 0,3-3,0, Work piece width min-max mm: 12-60, Min.-max. workpiece height in mm: 12-60, Min-max feed m/min: 18, Axis control: einlauflineal, Infeed table: Servo, Servo Einschubtisch: yes, mit Vakuum: 2 X 3 kw, Profile milling: yes, Machining cracks: yes, Power per lamp: 2-fach, Laser technology: yes, kW Leistung Laser: yes, Coil magazine: HL 84, Strip magazin: 2 X 1,5, Bevel milling: FK 8-fach Wechsler, radius milling: FK 13/Achsverstellung, Vertical grooves: Multiziehklinge MN 21 3 Profile, Grooves, slewable-controlled: PN 10, Nuten : yes, Radius scraper: yes, Servo copying: yes, Spraying system 2: A 20, Ersatzverleimteil : 5 kg, Number of sanding units: yes, Profile sanding top bottom: Einlauf und Auslauf, Barcode: möglich, Workpiece supp ...

Panel thickness: 12 - 60 mm Feed speed: 18 m/min Edge thickness: 0,3 - 3 mm for coil edges Equipment: Programmable fence at the infeed Squaring device: 2 x 3,0 KW Glue application unit: A34 double edge magazine for 2 coils Lateral pressure rollers, thickness programmable, 1 driven, 2 non-driven rollers End trims HL84/85, programmable change straight/chamfer, 2 motors 0,18 kW Rough trimming: 2 x 0,55 KW Contour trimming FK 13, 2 x 0,55 KW Profile scrapers PN10 Flat scrapers Buffing unit Controlls: HOMATIC NC21

Overview of the assembly: - Release agent spray unit top & bottom - Joining milling unit 2 x 4 kW - Glued part with workpiece preheating, 2 rolls, pressure zone C and QA34 application unit for PU with quick clamping system - autom. Adjustment pressure zone - Preparation for Lasertec activation unit - Hl84 cross-cut unit 0.8 KW - pneum. Adjustment pre-milling unit - Pre-milling unit Bf10 1.5 kW - Mould milling unit Fk11 Manual - Autom. Adjustment of chamfer to radius milling machines - Rolling side probe FK - Pneumatic adjustment FA11 for lateral displacement from the working area - Multi-drawing blade MN 21 autom. for a maximum of 5 different profiles. - Finishing unit (glue joint drawing blade and swabbing ridge) - Detergent spray unit top & bottom - powerControl PC22 Workpiece and edge parameters: - Workpiece width without edge min: - For workpiece thickness  ...

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Overview of equipment: - Workpiece support scissor design with roller support, 1000 mm extendable - Infeed ruler automatically adjustable - Fixed stop side left - Inlet interlock pneumatically controlled - Upper pressure via driven composite V-belt - Height adjustment electric - Workpiece transport device via transport chain with rubber support - Release agent spray unit top/bottom - Joint milling unit 2 x 3 kW - Gluing part A20 with 2 rollers, consisting of workpiece preheating, Quickmelt application unit with quick clamping system, 2-roll magazine, pressure zone C (auto-adjustable, with 1 pre-press roll and 6 repress rollers) - Cross-cut unit HL84 0.8 kW, with autom. Adjustment chamfer/straight as well as pneum. Adjustment flush/protrusion caps - Pre-milling unit 1.5 kW, pneum. Adjustment of bündi/protrusion milling machines - Mould milling unit FK11 with autom. Adjustme ...

Fixed stop side on the left. Brief description of the equipment: - Fixed stop side left - Workpiece transport device - Upper pressure - Control Power Control PC22 - Release agent spraying unit - Joining milling unit, 2 x 3 kW - Gluing part A20 Basic for rolls up to 3 mm and strip goods up to 20 mm, with melting unit with granulate container and quick-clamping system - Cross-cut unit, 2 x 0.8 kW, with pneum. Dissimulation - Lubricant spray agggregat - Pre-milled aggreagt 1.5 kW, pneum. adjustable - Mould milling unit FK13, 2 x 0.4 kW - Universal milling unit 4 kW, controlled, with infinitely variable axis - Multi-plastering device MN21 autom. - Finishing unit FA11, with finishing device, detergent application and buffing unit, pneum. adjustable -Noise protection - Free space for additional processing units Further equipment information: - Machine stand throughout f ...

Fixed side at the left Feedspeed 18 - 25 m/min Working width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mm Panel overhang 30mm Panel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations) Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mm Coil diameter 830 mm Equipment: Sprayers release agent Squaring device with 2 motors each 3 kW Edge heating Edge magazine for 2 coils, guillotine for edges up to 3 mm Glueing part A20 with quickmelt application Lateral pressure zone K, 1 driven and 6 after pressing rollers End trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kW Contour trimming, 2 exchange units Profile scraping PN10 Flat scrapers FA11 Sprayers cleaning agent Buffing Automation package straight/chamfer: -Automatic adjustment infeed fence -Automatic setting of pressure rollers -Pneumatic setting of end trims -Pneumatic setting of rough trims -Automa ...

Workpiece thickness: 8 - 90 mm, electronically adjustable Feed rate: 18-32 m/min frequency controlled Edge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mm Equipment: Inlet guide automatically adjustable via the control, extension 500 mm Joint milling unit: 2 x 3.0 KW workpiece preheating Gluing unit A34 edging magazine for roll Pressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the control Cutting unit WK14, straight, 2 motors 0.8 kW Pre-milling unit: 2 x 1.5 KW, pneumatic adjustment Form milling unit FF 12 automatic, 2 motors 0.4 kW radius/phase milling unit FF12 automatic 4 motors 0.4 KW universal milling aggregate controlled UF11, 4 kW Profile scrapers PN20 Glue scrapers Nozzles for detergent and anti-stick Polishing unit Control: Power Control PC22

Manufacturer: Homag PU und EVA, Type: KAL 310 310/6/A3/S2, Year: 2008, Control: NC 22, Software: Homag, Min-max edge material mm: 0,5-3,0, Work piece width min-max mm: 65, Min.-max. workpiece length in mm: 250, Min.-max. workpiece height in mm: 12-60, Min-max feed m/min: 10-25, Premilling: yes, Fine milling: yes, Application of separation agent: yes, IR zone: yes, Coil magazine: 2-fach, Mitre stations: HL 81, Bevel milling: yes, Corner tracing type: FF 12, 4 motors: Ja, Radius scraper: yes, Type of scraper: PN 10, Flat scraper: FA 11, 4 motors: Ja, Ersatzverleimteil : PU, Bonding part EVA: EVA, Buffing unit: yes, Separation agent setup: yes, Year :2008

Single-sided edge banding machine for machining of straight workpiece edges and for banding and post-processing of various edge materials in longitudinal and transverse passing. Automatic conversion from radius to chamfer and different edge and workpiece thicknesses. Control Power Control PC 22 OVERVIEW OF UNIT ASSEMBLY: – RELEASE AGENT SPRAYING UNIT – JOINING MILLING UNIT – GLUING PART A20 WITH 2 ROLLS Application unit PU 65 (Teflon-coated for PU gluing) – CROSS-CUT UNIT HL84 – PRE-MILLING UNIT – FK11 SHAPE MILLING UNIT – FREE SPACE UNI MILLING UNIT UF10 – PROFILE SCRAPER PN10 – FINISHING UNIT (with detergent information) – Feed rate 20 m/min – Total length 8635 mm 2. WORKPIECE AND EDGE PARAMETERS: – Workpiece width min: – For workpiece thickness 12-22 mm ¦ 60 mm* – For workpiece thickness 23-40 mm ¦ 105 mm* – Workpiece protrus ...

Key data: 20 mm, 60 mm, 8365 mm

I am selling a fully equipped edge banding machine HOMAG EDGETEQ S-500 KAL370 Ambition 2484, built in 2019: Configuration: Input stop servo-motor adjustable Manually adjustable joint milling Edge banding with preheating tanks 2 pcs. Material pressure zone can be adjusted by servo motor Pneumatically adjustable cross-cut saws Heavy milling top + bottom pneumatically adjustable Round unit 4-motor servo motor adjustable R2 / second set R1 included Swivel groove saw unit Radius scraper blade Multiradius servo motor adjustable Scraper blade surface can be pneumatically adjusted Polishing brushes Separator injection at the front Clean injection at the rear Working height adjustable by servo motor Material height 8-60mm Edge material thickness 0.4-12 (20)mm Feed speed 16 to 25m/min. Overall length including feed plate 8365mm Mileage status 833,000 meters. Input appar ...

Description: Technical data: tape thickness: 0.3 - 3 mm material thickness: 8 - 60 mm conveyor speed: 18 - 25 m / min The edgebander consists of the following aggregates: • 2 pre-milling machines for material processing (3 kW each) • material heating lamp • glue heating vessel • container with roller for applying glue to the material • push rollers • 2 stripping units (each 0.8kw) • 2 units with radial cutters for processing the upper and lower edges (1.5 kw each) • 2 postforming aggregates • 2 cyclings • polishing brushes with liquid injectors The edging is fully automated, which means that the height of the beam, pre-milling machines, rollers and all the settings of the cutter depending on the thickness of the material and the strip are adjusted on the main monitor. serial number: 0-200-19-0792, edge thickness: 0.3 - 3 mm, workpiece thickness: 8 -  ...

Description: serial number edgebander: 0-200-96-0454 supply 400 Y/230 V, 3 phases, 50 Hz maximum operating full load current 40 A fuse 50 A control voltage 24 V serial number return system: 0-284-96-1370 , supply 400 Y/230 V, 3 phases, 50 Hz maximum operating full load current 3,3 A fuse 16 A control voltage 24 V ATTENTION: Part marked in red NOT included Please also have a look at the pdf files of this machine  , serial number: 0-200-96-0454, Approx. Onsite Dimension. (l x w x h): 8,365 x 2,000 x 1,820 mm, weight approx.: 5,000 kg

Description: With Homag workpiece feeder TBL 100/25/12/F and Ligmatech workpiece return unit ZHR 30L/155/F  , edge thickness: 3 mm, workpiece thickness: 12 -60 mm, feed: 18 m/min, gluing unit: Ja, snipping unit: Ja, rough trimming unit: Ja, fine trimming unit: Ja, profile trimming unit: Ja, universal milling unit: Ja, edge sanding unit: Ja, flat scraping unit: Ja, profile scraping unit: Ja, edge buffing unit: Ja, control: powerControl NC 21, return system: Ja, total power approx: 40 kW, Approx. Onsite Dimension. (l x w x h): 10,000 x 6,000 x 1,700 mm, weight approx.: 4,000 kg

Manufacturer: Homag KAL 310/9/A20/S2, Type: 310/9/A20/S2, Year: 2005, Control: Powercontrol, Barcode: möglich, Min-max edge material mm: 0,3-3,0, Work piece width min-max mm: 75, Min.-max. workpiece length in mm: 250, Min.-max. workpiece height in mm: 10-60, Min-max feed m/min: 15-30, Axis control: yes, Infeed table: Winkelanschlag, Einlauflineal gesteuert: yes, Premilling: yes, Fine milling: yes, Application of separation agent: yes, IR zone: yes, Power per lamp: 400, Coil magazine: yes, Strip magazin: no, Mitre stations: yes, Radius milling axis adjustment: yes, 2 motors: FK 13, Magazin : 2 X 6 fach, Radius scraper: yes, Type of scraper: servo gesteuert, Scraper with axis adjustment: yes, Spraying system 2: yes, Bonding part EVA: PU Verleimteil, Buffing unit: yes, Barcode: möglich, Workpiece support: yes, Hover cussion table: yes, Return type: TFU 140/L/20/08/105 Bauyeshr 2018, FREE  ...

Aggregate for 4-Achs CNC to the extension for the 5-th axis

Aggregate for 4-Achs CNC to the extension for the 5-th axis

Board repair line with double end profiling line in top condition !! Workpiece parameters of the plates: Min.: 900 mm x 200 mm Weight min. : 17 mm Max .: 5000 mm x 1250 mm Max. Weight: 60 mm Weight: max. 150 kg < Accuracy: +/- 0.2 mm The portals have a max. Clock power of: max. 6 cycles / min The max. Partial performance: 18 parts / min (DEP line) Year of construction 2008 Condition: good (Original price of the line 2008 Euro 4.9 million) Consisting of: * Feeding station with feeding rollers, * Automatic vacuum lifting table for lengths up to 6 m * Conveyor systems * Repair line 1 * Turning station * Transfer service * Repair line 2 * automatic vacuum lifter for stacking (6m) * Stacking roller conveyor * Control cabinet with machine control * Profilfraessanlage * Stacking Tables; very well

Edge gluing machine - see picture Next: Edge gluing machine NEY-SENIOR SKM 100/3 gemaess Pictures

Edge gluing machine - see picture Next: Edge gluing machine NEY-SENIOR SKM 100/3 gemaess Pictures