Прес для гарячого шпону з масляним обігрівом OMC PL 90s

деревообробні станки / фанерні станки

вимагати більше фотографій

Wehrmann Holzbearbeitungsmaschinen GmbH & Co.KG
[ профіль дилера ]

пан Agne Odenram
32683 Barntrup
Germany

+49 (0) 5... телефон

затверджений
дилер

RESALE член з 2015

список машин (188)

відправити запит

додати до списку

відправити запит

Номер позиції: 164722610	Кількість: 1	Дата: 26.10.2024
Місцезнаходження: Німеччина

Ціна:	28,781 EUR
Виробник:	OMC
Модель:	PL 90s
Тип техніки:	Прес для гарячого шпону з масляним обігрівом
Опис:	Прес для гарячого шпону з масляним обігрівом OMC PL 90s HOT PRESS MODEL PL 90s 3000x1300 mm PS VBO TECHNICAL CHARACTERISTICS Platens dimensions 3000x1300 mm Stroke 400 mm Type of stroke Upstroke design (from bottom to top) Type of platen Assembled platens with coil and aluminum covering Total thrust 90 ton on 80% of the surface Pressing Cylinders N° 6 cylinders ø70 mm Specific Pressure 2.05 kg/cm2 on 100% of the surface 2.56 kg/cm2 on 80% of the surface Loading and Unloading Side3000 mm side Type of Heating system Oil boiler ? maximum temperature = 120°C Heating system specificationsElectric boiler 18 kW Opening Automatic by timer Control Board Standard Power supply 400V, 50Hz, 3ph Security device Safety rope around the press Red emergency Button Two Hand control Normative CE norms Press Structure The press structure is made of fe 430 beams assembled and welded together. The structure of both the fixed and movable platen is made of fe 430 beams assembled and welded together. The press is equipped with rack and pinion guide system to ensure a perfectly parallel movement during the closing/opening of the platens. Assembled platens with coil and aluminium covering Maximum oil Temperature 120°C Maximum specific working thrust 3-5 kg/cm² Maximum thrust of heating Fluid: 2 bar Our assembled platens with coil + aluminum covering are completely built in our metal workshop. Each coil, before being installed in the platen, is submitted to a strict leak test. A 3 mm calibrated sheet is placed on top of the coil. The platens are covered with aluminum sheet, that gives the platens an excellent surface finish and optimal heat propagation. Hydraulic system ?the hydraulic system consists of a double stage unit with submerged pump to reduce the noise and lubricate the rotating parts. ?quick closing/opening pump (high delivery- low pressure 35 L/min), pressing pump (low delivery-high pressure 1.6 L/min). ?2 hp electric engine ?the hydraulic unit is equipped with the following control/safety valves, installed on the tank: - maximum pressure valve: prevents to have too high pressure in the hydraulic system in case of electric or electronic control fault - pressure holding valve (retaining valve) - low releasing pressure valve (pre-releasing valve). It avoids dangerous ram hits inside the system - oil release control magnet Control panel and Electrical system The pressing parameters can be managed from the control board that is equipped with the following switches/ gauges: - temperature gauge to control platens temperature - Pressure regulating gauges and automatic pressure recovery system - general on/off switch - two hand safety switches to close the press - Timer for automatic opening with its own switch activates the automatic or manual opening of the platens after the work cycle. - off/on switch for heating resistance that switches the boiler off W41114335 when the set temperature is reached to restore the temperature, if there is any temperature decrease, in order to save power consumption. - heating pump on/off switch Safety systems - Timed bimanual control for press closing - Safety rope on the four sides of the press - Platen locking device for maintenance - Protection carter for the pinion/rack units - Safety stickers and warnings - Use and maintenance manual - the press is compliant with CE standards HOT PRESS MODEL PL 90s 3000x1300 mm PS VBO Price: ? 28.781,00 Optionals: Control panel and Electrical system Touch screen display - Programmable Logic Controller Colour full touch screen 7? display specifically designed to set the following: - temperatures - pressing time - daily setting of the heating system - automatic switching off of the heating system once the set temperature is reached and automatic recovery of the temperature - new system for the automatic setting of the pressure - option to save historical data/parameters - diagnostic system Price: ? 1.212,00 Mylar sheeting on 2 platens: Price: ? 651,00 Sensor to check the platen parallel stroke Price: ? 1.108,00 Electrical exclusion of 2 cylinders + Sensors to check the parallel stroke Price: ? 2.097,00 No. 1 intermediate platen Price: ? 4.510,00 seller offer No. resale 1110260
Машина в наявності:	Ні
Seller-item-No.:	1110260

Розповісти про цю машину на Facebook:

Прес для гарячого шпону з масляним обігрівом OMC PL 90s

Запит