Віконні установки OKOMA UF 2 EG mit Schleifeinheit

деревообробні станки / станки для виробництво вікон / Віконні установки

Gebr. Engelfried oHG
[ профіль дилера ]

пан Florian Engelfried
73432 Aalen
Germany

07361-986... телефон

затверджений
дилер

RESALE член з 2014

список машин (190)

відправити запит

додати до списку

відправити запит

Номер позиції: 164105254	Кількість: 1	Дата: 28.12.2024
Рік випуску:	Місцезнаходження: Deutschland

Ціна:	4,000 EUR
Виробник:	OKOMA
Модель:	UF 2 EG mit Schleifeinheit
Тип техніки:	Віконні установки
Опис:	Віконні установки OKOMA UF 2 EG mit Schleifeinheit вживана машина Number of spindles: 3 St. Number of tools: 2/3 St. Spindle diameter: 40/50 mm 1 OKOMA folding machine model UF 2 EG ------------------------------------- 1. Energy data: - Operating voltage: 3 phases, 380 V, 50 Hz. - Compressed air: Air requirement: 13 NL/min. Operating pressure: 8 bar up. Air: according to Pneurop 6611 2. Profile spindle 1: - Spindle arrangement: right - Power 11 kW - Speed 7000 rpm - Direction of rotation: synchronous and counter rotation - Spindle diameter 40 mm - Usable length 252 mm - Tool diameter max. 230 mm - U-movement of the profile spindle - Positioning vertically Drive: pneumatic cylinder 120 mm cycle for 2 tool positions Position sensor: limit switch - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch - Automatic immersion: immersion speed can be regulated for tear-free Fold over - Protective and suction hood with connecting piece 140 mm diameter. 3. Profile spindle 2: - Spindle arrangement: right - Power 11 kW - Speed 7000 rpm - Direction of rotation: counter rotation - Spindle diameter 50 mm - Usable length 272 mm - Tool diameter max. 230 mm - U-movement of the profile spindle - Positioning vertically Drive: pneumatic cylinder 90 mm cycle for 3 tool positions Position sensor: limit switch - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch - Protective and suction hood with connecting piece 140 mm diameter. 4. Fitting milling device EG: - Spindle arrangement on the right - Drive: three-phase motor 3 kW - Speed 6000 rpm - Spindle diameter 30 mm - Usable length 47 mm - Vertical positioning: none - Positioning horizontally Drive: Pneumatic cylinder forward-back Position sensor: limit switch (rear only) - Protective and suction hood with connection piece 80mm diameter 5. Stop: - 1st stop: in front of spindle 1 manual chip removal Quick adjustment via. parallelogram - 2nd stop: between spindles 1 G41212123 and 2 Chip removal: pneumatically adjustable - 3rd stop: after spindle 2 Fixed stop 6. Grinder with automatic immersion and immersion 7. Feed: - Roller distance from axle to axle 130 mm - Roll diameter 110 mm - Roll width 50 mm - Feed can be swiveled away - with pneumatic travel control 8. Support rail for milling: - Rail length: approx. 3000 mm - Adjustment range forward: approx. 100 - 600 mm 9. Electrical control: - Programmable logic controller: Siemens electronics PC control, 30 programs, 380 V., 50 Hz. - Power section: Siemens S 5 - Non-contact limit switches More pictures on request! --------------------------- (technical data according to manufacturer - no guarantee!) The data for this ad was created with ModulMWS - the software solution of LogoTech oHG. seller offer No. resale 1305-6828
Машина в наявності:	Так
Seller-item-No.:	1305-6828

Розповісти про цю машину на Facebook: