grinding diameter: 450 mm
grinding length: 1500 mm
centre
height: 225 mm
Control:
total power requirement:
kW
weight of the machine ca.: t
dimensions of the machine
ca.: m
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
-
T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or
MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ
1224/1242/1260
- Marposs tool measurement
- active
longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP
internal grinding with fluid sensor for T6 and T7
- semi-automatic
balancing by Elaso
integrated in the control surface for
T1/T2
- tailstock hydraulic with fine adjustment +/- 150
microns
- dresser on workpiece spindle side table mounted
-
dresser on tailstock side table mounted
- dresser on upper
table
- new service- and userfriendly housing
SPECIAL
EQUPEMENT:
Workhead with direct drive
- strongly
recommended for
non-circular grinding
- workpiece weight
flying max. 75kg
- workpiece weight between centres 150kg
-
water-cooled
B-axis with direct drive
- center height
225 mm
- extremely torsionally stiff
- highly accurate
positioning
- resolution 0.000001341°
-
water-cooled
Hydrostatic ball screw - x-axis
- wear-free,
as there is no contact during operation
- no loss of precision,
even during long-term use at full load and
maximum speed
-
no friction at low speeds
- no friction force backlash when the
direction of rotation changes
- translates even the smallest
rotational movements
- no stick-slip effect even at low
speeds
- no fluctuations in frictional torque due to ball
circulation
- higher axial stiffness compared to ball screws
-
significant improvement in damping, resulting in better workpiece
surface
finish and tool life
- no oscillations due to ball
circulation
- also suitable for high speeds and
accelerations
- cost-effective alternative to the linear motor
with greater precision and
significantly lower heat
generation
- significantly less power dissipation and, as a
result, no problems with swarf
on permanent
magnets
New hydraulic unit
- optimized temperature
control (chiller)
- Energy-saving
Only one pump controlled
by VFD
- Pressure monitoring
- monitoring of the hydrostatic
oil for
water content.
(Damage to the bellows is recognised
and detected prematurely)
-fine adjustment +/- 150
microns
Paper belt filter
375l – alternative
480l
Grinding mist extraction system –
emulsion
MECHANICAL OVERHAUL
-complete machine according
to Kellenberger protocoll
-new
painting
ELECTRICAL OVERHAUL
- new modern
Fagor CNC with BEMA HMI
- new electric cabinet
- new digital
drive technology
- replacement of all electrical cables, switches
etc.
- new absolute external scales in x- and z-axis
- new
absolute encoder (B-axis)
Grinding software
BEMA-Standard:
- workpiece B513074 zeroing
- grinding wheel
zeroing
- dressing diamond measuring
- corrections
-
external and internal surface grinding
- external and internal
angle grinding
(turning of the b-axis, dressing with straight
wheel)
- external and internal radius grinding (radius dressed on
wheel)
- semi-automatic traverse grinding
- workpiece
zeroing
- 2 dressing diamonds
- 1 dressing blade
-
dressing roll
- 3 flat dresser
- corrections
- Z-position
measurement
- GAP control
Optional grinding cycles
at no extra charge:
Profile plunge grinding:
- external and
internal profile plunge grinding with profile wheel
Profile
grinding:
- external and internal profile grinding with straight
wheel
Software thread grinding:
- single- and
multiple-start external and internal thread.
Grinding with
thread dressed on the wheel
Dressing of single and multi-groove
disc
Flank angle freely selectable.
Trapezoidal thread
grinding:
- Additional dressing of trapezoidal threads
possible.
Non-round grinding:
- external and internal
non-circular plunge-cut grinding
- external and internal
non-circular oscillating grinding
The
data for this ad was created with ModulMWS - the software solution of
LogoTech oHG.
