Opis: |
Szlifierki taśmowe HESS Junior
używana maszyna
Number of sanding units: 2 st. sanding width: 190 mm Sanding
height max.: 4-150 mm Hess Junior single wood sanding
machine -------------------------------- Pictures and videos
were taken at the customers site before dismantling. The machine
has now been dismantled and stored in our warehouse and is ready
for
dispatch.
Description: ---------------------------------<
br/>Basic structure: Stable, heavy welded construction made of
thick-walled rectangular hollow profiles with additional,
statically calculated stiffeners for optimal vibration
damping.
Offset sanding units with large-dimensioned belt
drive drums for slip-free belt running. Two-point extraction for
direct and airborne dust extraction with integrated blow-off
device. Sanding units in heavy steel plate construction as the
basis for vibration-damped, smooth belt running. All guides as
ball linear sets on hardened and ground shafts. Long-lasting
precision thanks to dust and dirt protection of the ball linear
sets. Contact roller and sanding shoe in a balanced ratio to the
sanding belt grain load. The large drive drums guarantee the full
transfer of the 5.5 kW drive power of the grinding motors to the
grinding belt. This enables the greatest possible chip removal.
Automatic machine stop triggered if the belt breaks. Visual
display on the control panel. Sanding shoe for finishing made of
special material with optimal heat dissipation and additional
sliding coating. Easy handling when changing the coating. Sanding
belt tension via appropriately dimensioned compression springs.
Sanding belt relaxation for belt change using a pneumatic device
for sensitive, distortion- free application of new belts. Upper
grinding unit and brush device (additional equipment) centrally
motor-adjustable.
Wood guide in the infeed area for hard
guide and pressure rollers mounted on both sides. Tilt-proof
transport of profiled workpieces on calibrated conveyor belts
with continuously adjustable feed speed.
Automatic machine
stop triggered by wood thickness control device.
Visual
display on the control panel.
Infeed table manually
adjustable via a fine-running, precise threaded spindle for lower
grinding chip removal via a scale (resolution 0.1 mm). The long
column table guide guarantees absolute parallel adjustment. The
flight circle adjustment to the outfeed table is achieved by
adjusting the height of the lower grinding unit via a precise
threaded spindle and scale display (resolution 0.1
mm).
Clear, user-friendly arrangement of all electrical
functional, operating and display elements on the front of the
machine: grinding unit below, grinding unit above, workpiece
transport device, grinding thickness adjustment, brushing device
above/below, belt utilization, operating display, fault display. All
motors are electrically protected against
overload.
Technical
data: --------------------------------
Grinding belt
speed: 25 m/sec. Grinding width: 190 mm Grinding thickness: 4 -
150 mm Shortest workpiece length: 280 mm Feed speed,
continuously adjustable 5 - 25 m/min. Grinding belt dimensions:
200 mm wide, 1850 mm long Electrical equipment in accordance with
VDE Electrical connection: 400 V., 3/N, 50 Hz. Pneumatic
connection: R 3/8, 6 bar, 80 NL Grinding units: 2 x 5.5 kW
Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection:
R 3/8, G41212123 80 NL, min. 6 bar, max. 8 bar Extraction air
volume: 2 x 2000 to 2500 m3/h 20 - 25 m/sec. Extraction
connection nozzle: 2 x 180 mm diameter, at the top of the machine
housing
External dimensions: without control cabinet
1750 mm wide, 1850 mm high, 1000 mm deep
with control
cabinet 1960 mm wide, 1850 mm high, 1000 mm deep
Working
height: 835 mm
in the range 4-20 mm only without guide
ruler Paint finish: RAL 7030 stone grey with RAL 1018 zinc
yellow
Additional equipment:
1 digital display for
motorized sanding thickness adjustment
1 device for
oscillating sanding belt utilization Device for oscillating
sanding belt utilization to increase the service life of the
sanding belts and improve the surface finish through motor-driven
sanding unit adjustment. Connected load: 0.12 kW, 380 V, 3/N, 50
Hz
1 brushing and finishing device for better surface finish,
integrated into the basic machine. Two special brush rollers
arranged one above the other, 150 mm diameter, in synchronous
motion for feeding. Separate height adjustment of the brush
rollers on precise slide guides for wear correction.
1
pneumatic workpiece blow-off device after the brushing and finishing
device
(Technical data according to the manufacturer, without
guarantee!)
The data for this ad was created
with ModulMWS - the software solution of LogoTech
oHG.
seller offer No. resale 1305-2758
|