| (For Europe) European
Edition |
(For Europe) European Edition (NHC4000)
Full 4th axis rotary table Interface for Through-spindle
coolant system (7.0 MPa, Variable Pressure Steps) (KNOLL) Coolant gun
for setup station side In-machine measuring system (spindle) optical
signal |
| Interface for Through-spindle Coolant
System (7.0 MPa, Variable Pressure Steps) (KNOLL/ Interlit) |
Interface for Through-spindle Coolant System (7.0
MPa, Variable Pressure Steps) (KNOLL/ Interlit) Interface for
mounting the high-pressure coolant system (separate type). Supplies
the high-pressure coolant to the tool tip from the center of the
spindle |
| In-machine measuring system (spindle)
optical signal transmission type touch sensor (RENISHAW, OMP60) +
workpiece setter function |
In-machine measuring system (spindle) optical
signal transmission type touch sensor (RENISHAW, OMP60) + workpiece
setter function |
| In-machine measuring system (table) touch
sensor (Magnescale) (tool length + diameter) |
In-Machine Measurement System (Table) Touch Sensor
(Magnescale) (Tool Length + Tool Diameter) The Magnescale touch sensor
mounted on the table allows the tool length and diameter measurements
and the tool breakage detection. During machining, the touch |
| Part program storage length 1 MB (2,560
m) in total + Registerable programs 1,000 in total |
Part program storage length 1 MB (2,560 m) in
total + Registerable programs 1,000 in total The storage capacity can
be increased to 1 MB, and up to 1,000 programs can be registered. |
| High-speed canned cycle |
High-speed canned cycle High-speed cutting can be
specified with one line of program. This function enables the user to
reduce programming time by adding a new cycle that can create a
high-speed, time saving complicated programs. |
| Coordinate system rotation |
Coordinate system rotation The shape specified by
a program can be rotated. By using this function, for example, if a
mounted workpiece is located at the position where the machine
coordinate is rotated, offset can be applied by the rotation command.
F |
| Workpiece position compensation for
rotary axis |
Workpiece Position Compensation for Rotary Axis
When a certain workpiece position on the rotary table is set as the
reference offset amount, the work coordinate system is created based
on the value of the current workpiece position offset amount
automat |
| Spindle Taper 7/24 Taper #40 (two-face
contact)/ Grip MAS |
Spindle Taper 7/24 Taper #40 (Two-face
contact)/Grip MAS This specification uses the
spindle No. 40 7/24 taper (Two-Face Contact) /Grip MAS tool holder.
The grip type and retention knob type of ATC are specified
separately. |
| Preparation for Center Through-spindle
coolant system |
Center Through-Spindle Coolant System It can
supply coolant through the holes of the spindle and tool. The coolant
supply path to the tool tip is a center-through type. Effective for
removing chips, cooling a machining point and prolonging a tool
life. |
| Retention Knob: Special (Center-Through)
(7/24 Taper #40) |
Retention Knob: Special (Center-Through) (Spindle
No. 40 7/24 taper) Equips machine for use with special center-through
coolant retention knob. Enables center porting of through spindle
coolant. Special retention knob is necessary with Through-spindle
c |
| Tool storage capacity 60 tools |
Tool Storage Capacity 60 Tools (Spindle No.40 7/24
taper) Ring-type magazine. Tool capacity: 60 tools (includes one tool
mounted in the spindle) Technical random address type. Max tool
diameter: - With adjacent tools: F70 mm (2.76 inch.) - Without
adjacen |
| Chip conveyor outside machine (rear
discharge, drum filter type) (STD) |
External Chip Conveyor (Rear Discharge, Drum
Filter Type) (Standard Specification) The scraper type chip conveyor
efficiently discharges chips in the machine into the container (order
separately) at the rear of the machine. The drum filter rotates
durin |
| Interface for Mist collector (duct only,
dia. 150 mm ) |
Mist Collector Interface (Duct Only, Ø150 mm
(dia.5.91 inch.)) I/F for mounting the mist collector that collects,
absorbs and dehydrates mist, dust particles and oily fumes generated
during machining using the filter. This specification includes the
D41252871 du |
|
|
| 10 external M-codes |
10 External M-Codes 10 M-codes are added for
general purpose use by customers. The terminal blocks are provided
for output/completion of the added M-codes. When the M-code is
specified, the signal is output to the terminal block relayed to the
relay ci |
| Manual pulse generator (separate
type) |
Manual Pulse Generator (Separate Type) ·Handheld
manual pulse generator facilitates set-up. ·Connected to operation
panel by robust coiled cord. ·Rear-surface magnet for storing on
operator panel or handy temporary placement as desired on the
machin |
| Voltage of Customer Factory 380 V |
Voltage of Customer Factory 380 V This machine is
shipped with voltage set to 220 V specification. Please arrange
transformer if necessary. (Caution) IF the setting is incompatible,
there is a possibility of trouble such as operation abnormality and
ala |
| Frequency 50 Hz |
Frequency 50 Hz This machine is shipped with
frequency set to 50 Hz specification. (Caution) IF the setting is
incompatible, there is a possibility of trouble such as operation
abnormality and alarm occurrence. Be sure to check the supply voltage
and fr |
| Setting Unit mm |
Setting Unit, MM The unit to be used for the
screen display and program commands is set to millimeter (mm).
Turning: MM specification for the turret Horizontal machining center:
MM specification for the tapped pallet |
| Islands, open pockets |
Islands, open pockets Islands - Programming
process can be greatly simplified because minimum input operation
is required even for the complex machining. Open pockets
Definition of open pockets eliminates tool paths with no machining
allowance, |
| Additional workpiece coordinate systems
48 sets |
Additional Workpiece Coordinate Systems 48 Sets In
addition to the standard 6 sets of work coordinate systems (G54 to
G59), the additional 48 sets of work coordinate systems are provided.
They are used when the standard 6 sets of work coordinates system |
| Screen display English |
Screen display English Language on MAPPS Screen:
English Language on MAPPS Warning Screen: English Language on NC
Screen: English Language on PC Screen: English |
| Cautionary points of Port of Discharge
(Please refer to the Description for further information) |
Cautionary points of Port of Discharge The freight
cost may vary according to the port of discharges, the estimation is
calculated by the ports as follows:Barcelona, Cork, Dublin, Genoa,
Gothenburg, Hamburg, Helsinki, Istanbul, Izmir, Izmit, Rotterdam, |