| Descripción: |
Einseitige Postforming-Kantenbearbeitungsmaschine WEHRMANN Combima DPF
Single sided postforming edge processing machine
Brand: WEHRMANN
Type: Combima DPF
New with 12 months warranty
Example with typical equipment; almost each equipment is
possible.
Please discuss your requirements with us
Technical data:
Machine control:
BECKHOFF route control with 15? Touch-Screen for pre-selection of
units and for saving programs.
The workpiece transport via precision roller chain R75 with
height adjustable top pressure.
Feed speed: max. V=6-30 m/min.
frequency controlled drive,
Top pressure: Motorical height adjustment via axis adjustment in
program
Right hand site equipped with 1 unit, width adjustment via NC axis:
1 Pre-milling unit
With 1 motor with vertical shaft, 400 V, 12,5 KW, 100 Hz, 6000
rpm.
Motor shaft Hydro D40
Swivable 90 - 180 degrees, move in/out for use
Left hand site Seite:
1 Infeed fence
Infeed device,
For guiding the workpieces on the infeed fence for the lengthwise
process, with 3 driven rollers.
1 Scoring motor from top
With motor 2,2 KW, 100 Hz, 6000 rpm.
1 Previous hogging unit
With 1 motor laying, 400 V, 12,5 KW, 100 Hz, 6000 rpm.
Motor shaft Hydro D40
Swivable 90 - 180 degrees
Move in/out for use
1 Previous hogging unit
With 1 motor laying, 400 V, 12,5 kW, 100 Hz, 6000 rpm.
Motor shaft Hydro D40
Swivable 90 - 180 degrees
Move in/out for use
1 Flat routing- and radius miller
Wit motor 6,6 KW, 100 Hz, 6000 rpm.
Motor shaft Hydro D40
Swivable 90 - 180 degrees
Move in/out for use
1 Flat routing- and radius miller
With Motor 6,6 kW, 100 Hz, 6000 rpm.
Motor shaft Hydro D40
Swivable 90 - 180 degrees
Move in/out for use
1 Laminate milling unit
for high-precise overhang milling, with vertical shaft
Motor 1 kW, 200 Hz, 12000 rpm.
1 Radius gap milling unit
With 1 hanging motor 400 V, 1 KW, HSK 25
working in feed direction
1 Flat routing unit
With horizontal shaft for milling the upper CPL area by set on the
U-profile.
1 Radius milling unit
For milling a W41014335 radius on the upper lengthwise edge at
U-profiles
mit Motor 4,4 kW, 100 Hz, 6000 rpm.
1 Laminate thicknessing unit
for milling the CPLs in radius area on the lower lengthwise edge
1 Laminate thicknessing unit
for milling the CPLs in radius area on the upper lengthwise edge
1 Laminate monitoring
EVA glue application on the ?radius gap?
With NORDSON - barrel melter
EVA glue application on the flat area of the CPL overhang
of the inner laminate site
Heating zone approx. 3000 mm long
Profile pressing tack with fix mounted sliding shoes and rollers
Cleaning via spraying nozzle from bottom
Milling unit 08.055 from top
With a motor 660 W, 400 V, 200 Hz
Buffing unit from top
With a motor 0,25 KW, FU-controlled, approx. 600-2000 rpm.
PU sealing of the inserting groove from top with Nordson barrel
melting
seller offer No. resale 1110210
|