| Descripción: |
Afiladoras de bandas HESS Junior
máquina usada
Number of sanding units: 2 st.
sanding width: 190 mm
Sanding
height max.: 4-150 mm
Hess Junior single wood sanding
machine
--------------------------------
Pictures and videos
were taken at the customers site before dismantling.
The machine
has now been dismantled and stored in our warehouse and is ready
for
dispatch.
Description:
---------------------------------<
br/>Basic structure:
Stable, heavy welded construction made of
thick-walled rectangular hollow
profiles
with additional,
statically calculated stiffeners for optimal
vibration
damping.
Offset sanding units with large-dimensioned
belt
drive drums for slip-free belt running. Two-point extraction for
direct
and airborne dust extraction with integrated blow-off
device. Sanding units
in heavy steel plate construction as the
basis for vibration-damped,
smooth belt running. All guides as
ball linear sets on hardened and
ground shafts. Long-lasting
precision thanks to dust and dirt protection
of the ball linear
sets. Contact roller and sanding shoe in a balanced ratio
to the
sanding belt grain load. The large drive drums guarantee the full
transfer of the 5.5 kW drive power of the grinding motors to the
grinding belt.
This enables the greatest possible chip removal.
Automatic machine stop
triggered if the belt breaks. Visual
display on the control panel. Sanding shoe
for finishing made of
special material with optimal heat dissipation and
additional
sliding coating. Easy handling when changing the coating. Sanding
belt tension via appropriately dimensioned compression springs.
Sanding belt
relaxation for belt change using a pneumatic device
for sensitive, distortion-
free application of new belts. Upper
grinding unit and brush device (additional
equipment) centrally
motor-adjustable.
Wood guide in the infeed area for hard
guide and pressure rollers mounted on
both sides. Tilt-proof
transport of profiled workpieces on calibrated conveyor
belts
with continuously adjustable feed speed.
Automatic machine
stop triggered by wood thickness control device.
Visual
display on the control panel.
Infeed table manually
adjustable via a fine-running, precise threaded spindle
for lower
grinding chip removal via a scale (resolution 0.1 mm). The long
column table guide guarantees absolute parallel adjustment. The
flight circle
adjustment to the outfeed table is achieved by
adjusting the height of the
lower grinding unit via a precise
threaded spindle and scale display
(resolution 0.1
mm).
Clear, user-friendly arrangement of all electrical
functional, operating and
display elements on the front of the
machine: grinding unit below, grinding
unit above, workpiece
transport device, grinding thickness adjustment, brushing
device
above/below, belt utilization, operating display, fault display. All
motors are electrically protected against
overload.
Technical
data:
--------------------------------
Grinding belt
speed: 25 m/sec. Grinding width: 190 mm
Grinding thickness: 4 -
150 mm
Shortest workpiece length: 280 mm
Feed speed,
continuously adjustable 5 - 25 m/min.
Grinding belt dimensions:
200 mm wide, 1850 mm long
Electrical equipment in accordance with
VDE
Electrical connection: 400 V., 3/N, 50 Hz.
Pneumatic
connection: R 3/8, 6 bar, 80 NL Grinding units: 2 x 5.5 kW
Feed:
0.75 kW Height adjustment: 0.18 kW
Pneumatic connection:
R 3/8, G41212123 80 NL, min. 6 bar, max. 8 bar Extraction air
volume: 2 x
2000 to 2500 m3/h 20 - 25 m/sec.
Extraction
connection nozzle: 2 x 180 mm diameter, at the top of the machine
housing
External dimensions: without control cabinet
1750 mm wide, 1850 mm high, 1000
mm deep
with control
cabinet 1960 mm wide, 1850 mm high, 1000 mm deep
Working
height: 835 mm
in the range 4-20 mm only without guide
ruler
Paint finish: RAL 7030 stone grey with RAL 1018 zinc
yellow
Additional equipment:
1 digital display for
motorized sanding thickness adjustment
1 device for
oscillating sanding belt utilization Device for oscillating
sanding belt utilization to increase the service life of the
sanding belts and
improve the surface finish through motor-driven
sanding unit adjustment.
Connected load: 0.12 kW, 380 V, 3/N, 50
Hz
1 brushing and finishing device for better surface finish,
integrated into
the basic machine. Two special brush rollers
arranged one above the other, 150
mm
diameter, in synchronous
motion for feeding. Separate height adjustment of the
brush
rollers on precise slide guides for wear correction.
1
pneumatic workpiece blow-off device after the brushing and finishing
device
(Technical data according to the manufacturer, without
guarantee!)
The data for this ad was created
with ModulMWS - the software solution of LogoTech
oHG.
seller offer No. resale 1305-2758
|