see side sheet below, with 2-spindle drill head Franz X. LINDNER SBS-2/2, spindle distance 300 mm, (translation 1:1)  ...

• more information

with NC round table WALTER 1000 mm, see pictures  ...

• more information

Drilling capacity: 32 mm Throat: 0 mm Spindle taper: 150   MACH-id    5460 MAKE        Alzmetal TYPE          Alzrapid 32 YOP             1998 SPECIFICATIONS Max. drill Ø steel      32 mm Max. drill Ø cast       40 mm Max. tap Ø      24 M Arm Length    725 mm Stroke pinole        150 mm Throat       400 mm Spindle Taper      4 ISO/Bt/Mk Speeds / ranges        3000 Rpm Table Length        1175 mm Table Width  &nbs ...

Morse cone MK 3 Drilling performance: Steel 28 mm Casting 32 mm Ihivikt Extension 700mm 3 Pre-shed0.1 - 0.2 - 0.3 mm/U 15 Spindle speeds 50 - 1220 rpm Spindle stroke 165mm max. distance spindle - base plate 1300 mm max distance spindle clamping block approx. 800mm Dimensions clamping cube 470mm550mm500mm high Clamping area foot 870700mm Hoe adjustment boom approx. 620 mm Spindle motor 1.1 / 1.7 kW Lifting motor 0.55 kW Outside mass: Length 1400 mm; width 700 mm; height 2300 mm Weight approx. 1100 kg

High-performance column drilling machine Offer number: 17469 Make: ALZMETALL Type: AB 4 SV Machine No: 18498 Built: 1987 Technical data: - Drilling capacity in steel ST 60 40 mm - Drilling capacity in steel ST 60 50 mm - Thread cutting device - Drilling spindle holder MK 4 - Drilling spindle stroke 180 mm - Drilling spindle speeds infinitely adjustable with pre-bedding - Level 1 - 80 - 210 rpm - Level 2 - 210 - 765 rpm - Extension 330 mm - 3 feeds 0.1 - 0.2 - 0.3 rpm - hydr. Feed cylinder for semi-autom. Workflow + Rapid Response - Table with 2 T-slots 720 x 360 mm - height-adjustable via rack with hand crank - max. distance table - dr ...

Alzmetall AC25 Column Drilling Machine Manufacturer: Alzmetall Type: AC25 / AS Year of Make: 1994 Condition: used, very good Clamping surface (left-right): 390 mm Clamping surface (front-rear): 420 mm Control: electronic control Quill stroke: 120 mm Speed range up to: 5000 rpm Number of transmission stages: 2 Tool holder: MK 3 Connected voltage: 400 V Mains frequency: 50 Hz Total height approx.: 1.90 m Weight approx.: 350 kg Quill stroke with programmable feed Work table can be swivelled away & height-adjustable Machining values can be set via selection. Accessories: Coolant Pump, Various Tool Quick Change Holders, Documentation

Drilling capacity in St 60: 40 mm threading in St 60: M 24 threading in GG 20: M 30 Short spindle: MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm Machine table - usable table surface: 514x360 mm T-Slots Amount - Width - Distance: 2 x 14 x 224 mm Distance spindle - machine table min./max.: 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: 7 TFT - LCD display with touch function: manual input of spindle speed Setpoint, speed display actual value, integrated drilling depth display with touch Zero point transfer, virtual drilling de ...

: 40 mm : M 24 : M 30 : MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm : 514x360 mm : 2 x 14 x 224 mm : 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: - Mushroom pushbutton (latching) for EMERGENCY STOP - Reversing switch for right-left rotation - Motor protection switch - Speed adjustment stepless - Speed display digital - Feed overload protection - Protection IP 54 - Connector (fully assembled, cable length 2 m) - Spindle protection with electrical protection The data for this ad was created with ModulMWS - the software s ...

number of spindles: 3 bore capacity in steel (diameter): 40 mm bore stroke: 180 mm weight of the machine ca.: 2,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.  ...

• more information

: 55 mm : M 30 : M 36 : MK 4 spindle turning speed - stepless: 70-1.200 U/min spindle stroke: 140 mm throat: 300 mm column diameter: 145 mm : 615x430 mm distance spindle /table: min./max. 150/735 mm : 2 x 14 x 224 mm feed: 0,1 + 0,3 mm/U Machine height: 1850 mm weight: 380 kg drive motor: 1,8/2,9 kW Standard equipment: - Lockable main switch with motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP - Infinitely variable speed adjustment - Digital speed display - Feed overload protection - Protection class IP 54 - Spindle protection with electrical fuse Item 20.1 Thread cutting device with foot switch, for thread cutting with Stop, max. 6 threads / min., (Thread cutting ...