Maximum punching force: 1100 kN Maximum shear force: 1700 kN punch ing: 510 mm support table hole 31 in 25 mm flat steel: 500 x 22 mm hydraulic holder for the flat steel knife kago n weight: approx. 5000 kg ; Very good  ...

• more information

Offer 22562 Hydraulic profile and bar steel shears with notching device and hole punch Specifications: - Flat steel scissors - Flat steel - 500 x 18 mm - or: 300 x 22 mm - Profile steel shears - L- and T-irons at 90° 120 x 13 mm - at 45° 90 x 10 mm - Round steel 45 mm - Square steel 40 mm - Notcheter - With square notch for sheets up to 13 mm - Jack width / depth 65 / 85 mm - With triangular notch for sheets up to 13 mm - Notch depth 70 mm - Hole punch - Punching force approx. 80 t - Projection 510 mm - Stroke approx. 10 to 29 mm - perforates in steel up to 39 mm Ø in 16 mm - perforates in steel up to 30 mm Ø in 20 mm - ...

Max. punching capacity: 600 kN Max. shear power: 800 kN Punches 27 mm holes in 16 mm steel Shears on the flat steel shears to 400 mm up to material thickness of 16 mm steel Hydraulic hold-down device on flat steel shears Further technical data on request With an assortment of punches and dies as desired Weight: approx. 2,000 kg

Max. punching capacity: 600 kN Max. shear capacity: 1000 kN Punches 20 mm holes in 19 mm steel Shears on flat steel shears to 500 mm up to material thickness of 12 mm steel Further technical data on request With an assortment of stamps and dies as desired  ...

• more information

Max. punching capacity: 600 kN Max. shear capacity: 800 kN Punches 27 mm holes in 16 mm steel Shears on the flat steel shear to 400 mm up to material thickness of 16 mm steel Hydraulic hold-down device on flat steel shear Large support table on the punching side with stops Further technical data on request With an assortment of stamps and dies as desired Weight: approx. 2,000 kg

4-way comb. Section steel shears make PEDDINGHAUS type Peddimaster 28/40 HMachine -No: 4421050787006Technical specifications:FLAT STEEL SHEARSFlat steel with little deformation up to: 300 x 10 mmor: 250 x 10 mmor: 200 x 11 mmor: 75 x 15 mmKnife cutting length: 300 mmWorking height: 830 mmPROFILE STEEL SHEARSShear cross section max .: 1300 mm²Infinitely adjustable stroke: 10 - 26 mmL-steel 90 ° cut up to: 80 x 8 mmL-steel 45 ° cut up to: 50 x 6 mmRound steel: 29 mmSquare steel: 25 mmWorking height: 1088 mmNOTCHERSquare notcher sheets up to: 8.0 mmL-steel up to: 60 x 6 mmU-steel in the flange: 50 x 25/60/65 mmI-steel in the flange: 80/100 mmNotch width / notch depth: 42/55 mmHOLE PUNCHPunch ...

4-fold combined profile steel shears make PEDDINGHAUS type Peddimaster 80/110, built in 1993Technical specifications:FLAT STEEL SHEARS:500 x 18 mm:400x19mm:300x22mm:200x25mmKnife length: 510 mmPROFESSIONAL STEEL SHEARSAngle steel 90°: 120 x 13 mm:150x100x12mmAngle steel 45°: 100 x 10 mmRound bar: 45 mmSquare steel: 40 mmSQUARE NOTCHSheets up to: 13 mmLatch width: 65 mmNotch depth: 85 mmHOLE PUNCHPunching force: 80 tProjection: 510 mmStroke continuously adjustable: 10 - 30 mmHoles: 30 in 20 mm:27 in 20mmGENERAL MACHINE DATANumber of strokes: 22 / 16 h/minOil filling: 80 lDrive power: 7.5 kWWeight approx.: 2450 kgExternal dimensions approx.: 1990 x 850 x 1890 mmwith- stop table- 2 footswitch ...

round bar steel: 45 mm square edge steel: 40 mm L-beam: 120 x 13 mm flat steel: 500 x 12 mm punching pressure: 60 t throat: 510 mm : 500 x 12 oder 400 x 16 mm punch diameter: 27 in 17 mm punch diameter: 39 in 12 mm oil volume: 80 l total power requirement: 7,5 kW weight of the machine ca.: 2,4 t dimensions of the machine ca.: 1,8 x 0,9 x 1,8 m Hydraulic machine with 5 stations so punching, notching, shearing flat iron, angle iron, solid material, punching with hand lever, profile steel side with foot switch. Punching discharge: 510 mm! All performance data refer to a material strength of 450 N / mm². Electric 380 volt The data for this ad was created with ModulMWS - the software solution  ...

round bar steel: 45 mm square edge steel: 40 x 40 mm L-beam: 120 x 13 mm flat steel: 500 x 12 mm Punch power: 600 kN hole punching press: throat: 510 mm hole punching press: capacity (dia. x thick.): 27 x 17 mm hole punching press: capacity (dia. x thick.): 39 x 12 mm oil volume: 80 l total power requirement: 7,5 kW weight of the machine ca.: 2,4 t dimensions of machine L x W x H: 1,80 x 0,90 x 1,80 m - hydraulic - Accessories: tool cabinet with various punches and dies, length stop 1850 mm with limit switch The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Scissors: for flat steel: 80 x 10 mm Shear: For L & t 90 / 45 ° 70 x 70 x 7/50 x 50 x 6 mm Rod steel scissors around until: 28 mm square up: 25 mm Notching device for material thickness up to: 7 mm Drive motor: 380 V, 1.3 kW Weight: 400 kg Space: 1000 x 650 x 1480 mm  ...

• more information