Alzmetall AB4SJ Tool holder MK4 automatic feed with 3 feed speeds 2 shoot stages and infinitely variable speed control right left barrel, thread cutting device Cooling agent device in the foot Round table with holes without rev counter Machine hood modern made of plastic with cracks and loechers Speed: 80-710 rpm Table diameter: 450 mm Max distance from spindle to foot: 1200 mm Extension to center spindle: 170 mm Machine hoe approx. 200 cm Bt323s8 SPECIAL PRICE due to visually poor condition according to photos, technically usable condition, the drill is not locked at the shaft drill spindle tool holder in the rotational motion (see photos). If the drill is not firmly in  ...

see side sheet below, with 2-spindle drill head Franz X. LINDNER SBS-2/2, spindle distance 300 mm, (translation 1:1)  ...

• more information

with NC round table WALTER 1000 mm, see pictures  ...

• more information

Morse cone MK 3 Drilling performance: Steel 28 mm Casting 32 mm Ihivikt Extension 700mm 3 Pre-shed0.1 - 0.2 - 0.3 mm/U 15 Spindle speeds 50 - 1220 rpm Spindle stroke 165mm max. distance spindle - base plate 1300 mm max distance spindle clamping block approx. 800mm Dimensions clamping cube 470mm550mm500mm high Clamping area foot 870700mm Hoe adjustment boom approx. 620 mm Spindle motor 1.1 / 1.7 kW Lifting motor 0.55 kW Outside mass: Length 1400 mm; width 700 mm; height 2300 mm Weight approx. 1100 kg

Alzmetall AC25 Column Drilling Machine Manufacturer: Alzmetall Type: AC25 / AS Year of Make: 1994 Condition: used, very good Clamping surface (left-right): 390 mm Clamping surface (front-rear): 420 mm Control: electronic control Quill stroke: 120 mm Speed range up to: 5000 rpm Number of transmission stages: 2 Tool holder: MK 3 Connected voltage: 400 V Mains frequency: 50 Hz Total height approx.: 1.90 m Weight approx.: 350 kg Quill stroke with programmable feed Work table can be swivelled away & height-adjustable Machining values can be set via selection. Accessories: Coolant Pump, Various Tool Quick Change Holders, Documentation

Drilling capacity in St 60: 40 mm threading in St 60: M 24 threading in GG 20: M 30 Short spindle: MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm Machine table - usable table surface: 514x360 mm T-Slots Amount - Width - Distance: 2 x 14 x 224 mm Distance spindle - machine table min./max.: 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: 7 TFT - LCD display with touch function: manual input of spindle speed Setpoint, speed display actual value, integrated drilling depth display with touch Zero point transfer, virtual drilling de ...

: 40 mm : M 24 : M 30 : MK 3 bore stroke: 120 mm throat: 293 mm column diameter: 115 mm : 514x360 mm : 2 x 14 x 224 mm : 117/701 mm feed: 0,10 + 0,20 mm/U spindle turning speed range: 160-2.250 UpM total power requirement: 1,45/1,9 kW height of the machine: 1840 mm weight of the machine ca.: 285 kg Standard equipment: - Mushroom pushbutton (latching) for EMERGENCY STOP - Reversing switch for right-left rotation - Motor protection switch - Speed adjustment stepless - Speed display digital - Feed overload protection - Protection IP 54 - Connector (fully assembled, cable length 2 m) - Spindle protection with electrical protection The data for this ad was created with ModulMWS - the software s ...

number of spindles: 3 bore capacity in steel (diameter): 40 mm bore stroke: 180 mm weight of the machine ca.: 2,3 t The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.  ...

• more information

: 55 mm : M 30 : M 36 : MK 4 spindle turning speed - stepless: 70-1.200 U/min spindle stroke: 140 mm throat: 300 mm column diameter: 145 mm : 615x430 mm distance spindle /table: min./max. 150/735 mm : 2 x 14 x 224 mm feed: 0,1 + 0,3 mm/U Machine height: 1850 mm weight: 380 kg drive motor: 1,8/2,9 kW Standard equipment: - Lockable main switch with motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP - Infinitely variable speed adjustment - Digital speed display - Feed overload protection - Protection class IP 54 - Spindle protection with electrical fuse Item 20.1 Thread cutting device with foot switch, for thread cutting with Stop, max. 6 threads / min., (Thread cutting ...

bore capacity in steel (diameter): 40 mm throat: 293 mm bore stroke: 120 mm spindle taper MT: 3 column diameter: 115 mm table surface area: 514 x 360 mm spindle turning speed - stepless: 160 - 2250 U/min total power requirement: 1,0/1,6 kW weight of the machine ca.: 0,285 t dimensions of the machine ca.: m Condition: new / unused: The machine can be viewed under current.: 37981 400 V, 50 Hz, colour: light grey RAL 7035 continuous speed control, digital speed indication, push button for emergency switch off, turning switch for clockwise/counterclockwise rotation, motor protection switch, IP 54, connecting plug, finish: structure varnish, new spindle bearing, new step pulleys, belts aso. ope ...