| Direct measuring system |
Direct path measuring system |
| Cabine |
Full protection cabin |
| Dynamic package for DMF 260 linear
(Y1100) |
Dynamic package for DMF 260 linear (Y1,100 mm)
linear drive X-axis with 80 m/min // 262.48 ft/min rapid move XYZ
80/60/60 m/min // 262.48/196.86 ft/min, Acceleration XYZ 5/6/6 m/s²
// 16.4/19.68 ft/s² Active chiller for main spindle and Linear motor
mag |
| Rigid table with integrated rotary axis
(leftside) |
Rigid table with integrated round table d 1050 mm
// 41.3 in, located in the left working area table load max. 1,200
kg// 2,644 lbs hydraulic clamped in position |
|
Table surface 3200 x 1100 (Ø 1050) mm |
| Clamping hydraulics,2
circuits,Rigid-/Round table |
Clamping hydraulic for rigid/integrated round
table, 30-240 Bar, 2 circuits |
|
Rotation speed max.4. Axis 50 rpm |
|
Distance between T-Slots 100 mm |
|
Number of Slots 11 |
|
Slot width 18 mm |
| Removable partition wall DMF260
(Y1100) |
Partition wall removable for pendulum machining
DMF260, 2 working spaces (possible with integrated round table) |
| Tool magazine 60 places
SK50/HSK-A100 |
Tool magazine 60 places SK50/HSK-A100 Chain type
with double gripper |
| Mechanical setup station |
Mechanical setup station SK50/HSK-A100 |
| Load support for tool magazine |
Load support for tool magazine SK50/HSK-A100 with
2 pockets at the stairs to magazine |
| Spindle speed 20 - 10,000 rpm HSK-A100
430 Nm |
Spindle speed 20 - 10,000 rpm HSK-A100 for tool
taper according to DIN69893 with power 52/42 kW // 69.7/56.3 hp with
torque 430/300 Nm (40/100% ED) (differently from standard) |
| 3D quickSET elevated constructuion |
3D quickSET Tool kit for control and compensation
of the cinematic accuracy of 5 axis machine configurations include
additional fixture for elevated construction (only with option touch
probe) |
| Tool laser measuring Blum |
Laser tool measuring Blum (not with TT 140
possible, for pendulum machining please order 2 pieces) |
| Oil mist separator |
Oil and emulsion mist separator system 2 pieces
per machine implemented in right and left cabin side wall. mechanical
filter system 2x1600 m³/h |
| Signal lamp 4-colour |
Signal lamp 4-colour Red: general error Yellow:
intervention necessary Green: automatic mode Blue: set-up mode |
| Air blast through spindle centre |
Air blast through spindle centre activated by M
function, maintained air, low oil rate possible |
| Internal Coolant Supply 80bar/980l
frequency controled |
Internal coolant supply (ICS) with paper type
filter Papertype-Filter 20-80 Bar // 290-1160 psi frequenzy controlled
980 l tank // 258.8 gallon inclusive 2 rotating clear window, air
purge for linear measuring system, rotary joint for main spindle |
| Chip flushing for working area |
Flushing for working area Additional flushing of
the working area doors and cabin sidewalls, Bed flushing included |
| Double cartridge filter,25 µm |
Double cartridge filter, Finesse of filtration 25
µm (only in combination with internal coolant) |
| Coolant tempering for internal coolant
980l |
Coolant tempering for internal coolant unit 980l /
259 gallon: Heating capacity max.: 4 kW / 5.3 hp Cooling capacity
max.: 4 kW / 5.3 hp (only in combination with internal coolant unit
980l) |
| Door drive for working area D41152871
doors |
Door drive for working area doors Open / close -
activated by two-hand-operation at the control panel Safety sensor
technology for prevention of accidents |
| MPC Machine Protection Control |
MPC Machine Protection Control Machine protection
by quick shutdown |
| proTIME |
proTIME Visualisation of remaining runtime,
remaining workpieces and the machine state |
| Application Tuning Cycle ATC |
Application Tuning Cycle ATC programmable feed
parameter selection for machining task: accuracy/surface/speed |
| Operation mode 4 |
Operation mode 4 Process monitoring in the
production Manual intervention with open doors of machining area.
Release after check list has been filled in. |
| Turning/Milling cycle |
Turning / milling cycle For the machining of
internal and external diameter using spindle orientation |
| DXF Reader |
DXF-Raeder: Open CAD files Extracting of counters
and drilling positions directly in G-code and ShopMill programs
Supported elements: drilling positions and contours |
| angularTOOL |
angular TOOL Technology cycle for programming of a
360 degree rotatable angular head tool |
| Laminated safety glass |
Laminated safety glass for Windows in the two
front doors |
| Exhibition design DMF |
Exhibition design DMF chiller of electrical
cabinet painted in electrical cabinet color; lighting of tool
magazine; DMG-MORI set of labels; paper version of electrical
plan |
| Stop block HSK-100/SK50/CAT50 |
Stop block HSK-A100/SK50/CAT50 |
| Digital Manufacturing Package |
Digital Manufacturing Package (1) IoTconnector
Allows the use of the Online services from DMG MORI (2) Machine Data
Connector (MDC) Standardized machine data interface Protocols: OPCUA,
MTConnect, MQTT (3) NETservice Qualified support through
internet-b |
| Messenger V4 |
The latest version of DMG MORI Messenger displays
web based the machine live status. It allows to analyze the machine
run-time, downtime, alarms in individually configurable dashboards
and transparently shows the actual status in the manufacturing
shop |
| Service Agent |
Service Agent Overview of all maintenance work on
the machine |
| Special equipment |
SK001 Preparation for Hofmann RW/NC 400 with
direct measuring system ready to plug right workspace Y-0404
Micro-Aerator: For clean coolant (50HZ) |