Screw diameter [mm] 22 Injection volume [cm3] 22.8 Injection weight [g] 20 Injection pressure [bar] 2400 Electric-hydraulic equipment Nominal power of the pump motor [kW] 7.5 Heater power [kW] 3.7 Dimensions and weight Net weight with control cabinet [t] 2.6 Dimensions (L x W x H) [m] 3.20x1.30x1.80 m

Demag Ergotech Compact 250-80 Year of Make: 1995 Injection unit: Screw diameter: 18 mm Injection weight: 20 g Spray pressure: 2400 bar Dosing volume: 22.8 ccm Clamping unit: Clamping force: 25 t Tiebar spacing: 280x280 mm Size of the clamping plates: 410x410 mm Ejector: hydraulic Clamping unit: hydraulic Control: NC4 Additional equipment: Air Valve x 2 Hydraulic core pull x 1 Hardened injection unit - Bimetal Original Demag tool crane: chain, electrically controlled, 2 lifting speeds Metrics: Weight: 2600 kg Length/Width/Height: 3.20x1.30x1.80 m Drive: Pumps/motor: 7.5 kW Heating capacity: 3.7 kW Total power: 11.2 kW All offered machines are started by ...

Molding machine of Mag Type: Ergotech 100-310 compact control: NC 4 year of construction: 1997 Clamping unit Clamping force t 100 Gap mm: 500 Holm dimension mm: 420 x 420 min/max height mm: 250 Plate size: 590 x 590 Injection unit Screw diameter mm: 35 Injection weight gr: 149 Injection volume cm m³: 168.3 Spray pressure bar: 2640 Dimensions and weights Dimensions Lxwxh m: 4.4 x 1.4 x 1.8 machine weight kg: 4400 Miscellaneous EUROMAP 12,Pneumatikventil

Molding machine of Mag Type: Ergotech 25-80 compact control: NC 4 year of construction: 1994 Clamping unit Clamping force t 25 Gap mm: 350 Holm dimension mm: 280 x 280 min/max height mm: 105 /. Plate size: 390 x 390 Injection unit Screw diameter mm: Gr 22 injection weight: 37 Injection volume cm m³: 42 Injection pressure bar: 2061 Dimensions and weights Dimensions Lxwxh m: 3 x 1.05 x 1.9 machine weight kg: 1550

emag injection molding machine Type: Ergotech 80-310 compact control: NC 4 year of construction: 1994 Clamping unit Clamping force t 80 Injection unit Screw diameter mm: 35 Injection weight gr: 149 Injection volume cm m³: 168.3 Spray pressure bar: 2020 Dimensions and weights Dimensions Lxwxh m: 3.9 x 1.4 x 1.9 machine weight kg: 3600

DEMAG 150T NC4 ERGOTECH 150/500-610 COMPACT 2 hydraulic cores 1 pneumatic core ...

• more information

This DEMAG Ergotech 150-610 Compact Injection Moulding Machine was built in the year 1998 and has 13860 pump hours. It is equipped with a Demag NC IV control unit. The machine has a clamping force of 1650 kN and a screw diameter of 40 mm. ...

• more information

Year of construction: 1997 Clamping unit - Clamping force: 800 kN - Handle width: 400 x 400 mm - Tool installation height 250/ 700 Injection unit - Shot weight (PS): 149 g - Screw diameter: 35 mm Remark: - Dispensing without sprue picker and external Peripherals - Displacement measuring system for Screw movement changed - Hydraulic motor for worm drive Switched in 2019 - 02/2022 Hydraulic hoses changed - Cavitation in pump - Plasticizing unit is needed as a replacement for other machines and is not included! General - 2 core pulls -Machine is still in operation Pump running time - approx. 114,000h Other: -Submission expected June/ July 2024 -for the prod ...

1998 Demag Ergotech NC4 330-2300 compact As shown The machine is in good condition. Currently under power and can be viewed in production at a short notice. Year of construction: 1998 Closing force: 3300kN Closing force: 3630kN Spacing of the columns: 710x630mm Clamping platen: 1040x950mm Mould installation height min.: 330mm Mould installation height max.: 330mm Opening stroke max.: 675mm Ejector stroke: 200mm Ejector force: 80kN Ejector retraction force: 35kN Screw diameter: 80mm L/D ratio: 20 Max. Shot volume: 1583ccm Injection pressure: 1437 bar Other: 2014 general overhaul (new cylinder, screw, RSP, Smartdrive retrofitted, for pump speed control, heating band insulati ...

1996 Demag Ergotech NC4 100-310 compact As shown The machine is in good condition. Currently under power and can be viewed in production at a short notice. Year of construction: 1996 Closing force: 1000kN Clamping force: 1000kN Distance of the columns: 400x400mm Clamping platen: 580x590mm Mould installation height min.: 250mm Distance between platens max.: 750mm Opening stroke max.: 500mm Ejector travel: 150mm Ejector force: 41kN Ejector retraction force: 15kN Screw diameter: 35mm L/D ratio: 20 Max. Shot volume: 168ccm Injection pressure: 2020 bar Other: Euromap 12 interface, 4-axis handling from Dürrschmidt, RSP exchanged 10/2023, SD card drive Find more here - / Conta ...