| Description: |
CNC ROUTER for milling stone etc CNC-STEP High-Z S-400/T
Specifications / Technical Data S-400/T
CNC-Portal-Router /
CNC-Engraving machine
Grabite marble soapstione
slate engraving photo engraving, milling ..
With the purchase of the T-variation of High-Z cnc-router you get
a proven technology with a certain icing of the cake. High-Z/T
cnc-routers was conceived for once more precision (repetition
precision approx. 0,02mm) and especially for higher traverse
speed.
Because of the used ball screws the
High-Z/T 3D-cnc-engravers achieves a fantastic precision and an almost
unmeasurable back lash of approx. 0,01mm. At the same time there are
high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min )
possible.
With this cnc-machines you're
able to carry out an engrave and mill speeds of approx. 4500 mm/min.
and express travels up to 6500mm/min.
Here's a
video on a unloaded drive with the new High-Z / T.
This 3D-milling-machine series is usable in the industrial field
as well as for works like engraving, milling, drilling, measuring,
cutting and measuring out systems as for example adhering of adhesive
on 3D outlines.
All cnc-machines are being
delivered with black energy-chains on all axis, which allows a better
cabling management. Also, all cnc-engraving-machines are equipped with
an emergency stop button. An additional emergency stop you find in
front of the controller.
Basic equipment of
all High-Z CNC-milling machines:
Software ConstruCAM-3D
limited ( from S-720 and S-400/T ) included
Contact free reference switch and emergency stop button as well as
22mm thick linear guide ways and individually adapted screw nuts
------------------------------------------------------------------
--------------
Equipment / Productdetails:
oDrive : 4 stepping motor by Nanotec with 1600 steps/rev
(1/8 Step)
o2 motors for constant tension and compression during
milling operation on X-Axis
oGuide ways X and Y axle 22 mm / Z
Axis 16mm, grinded and with 61hrc hardened surface
oFeed through
of long workpieces possible, because there's no belt drive at the end
of the X-axle
oBall bearings at both sides of ball screws on
X and Y axis
oTraverse speed of rapid feed: max. 7000 mm/min
oTechnical resolution : 0,00625 mm ( 1/8 Schritt )
oReversal
error max.: +/- 10µm ( 0,01mm )
oTable size / clamping area:
730 x 400 mm
oTraverse Paths: X=400 mm; Y=280 mm; Z= 110 mm
oReference- and limit switch on all axes
oDouble safety
emergency stop button
oEnergy chain for clean cabling
oTotal
dinemsions incl motors: L x W x H = appr. 730 x 520 x 500mm
oMilling Motor anchorage: Euroneck Ø43mm
oincl. Software WIN
PCNC Light (optional WIN PCNC Economy, USB or professional)
oincl. Software ConstruCAM-3D limited ( recommended sell price
full version 1902.81 EUR)
oModular frame for universal
application
oWeight appr. 31 kg
oComplete machine Includet 4
driver microstep controller 4 x 3,5 Ampere
oAn approx.
30-minute long introduction during pick up and an unlimted telephone
support are included.
oAn approx. 2 hours long introduction
and an installation of software on your brought note book/ PC as well
as a explanation of fundamental terms of Corel Draw etc. possible,
too.
------------------------------------------------------------------
--------------
Technical data contained in the
price TÜV-certified control system, tailored to the CNC milling
machine / CNC engraving machine:
o 4-Channel
Stepper motor -CNC-Controller with actual SMD-Technology
o
Main voltage 115 - 240 Volt / 47 - 63 Hz.
o Motor current 4 x
3,5 Ampere
o Microstep controller Resolution 1/10-Step / 2000
Steps/Rev.
o 4 Connections for 4 brushless Motor / Stepper
motor
o Connection with parallel port and Software WIN PCNC
Light, Economy or USB with WIN PCNC USB or
Profi version. (
Also possible:MACH3, USBCNC, NC-Easy LINUX EMC and LINUX CNC and much
other
stepper driver software.)
o "Sleep-Function"
for controlling current down
o Oszillation motor-Connection
24 Volt by PWM controllable ( for example: Tangential knife ) or
24 Volt constant for motor Break by ST-plug
o 2 relais for
maximum 1200 Watt by Software switchable (up from WIN PCNC Light), 230
Volt,
max. 6,0 C41144965 A / Plug (for example Air compressor,
cooling, exhaust, dust extraction).
o 0 - 10 Volt for
connecting a HF converter for an high frequency spindle
o 12
Status-LEDs for monitoring all important function (Power, Toggle,
Move, X, Y, Z, C; Overheat,
Emergency stop, Relais: Spindle
/ Cooling, Short Circuit)
o Connection possibility of 4 end-
or. Reference switches and one Emergency Stop switch
o Motor
connection by D-Sub 9-pin. (C-Axis: 15-pin.)
o Emergency-Stop
Switch
o Overheating protection
o Short circuit
protection
------------------------------------------------------------------
--------------
More information, several
videos about the applicability of the machine and customer
implementations can be found here.
The name High-Z
derives from the fact, that the machines lower contruction allows to
work on pieces with unlimited height.
Because almost 90%
of the demand for a 5-channel microstep control and subsequent
expansion of an additional axis, the production of the 4-channel
control won't be produced any more in the near future!
Take advantage of the High-Z 3D-cnc-router as a plasma cutting
machine for plasma cutting of steel, etc. Infos here !
Software Process for our cnc-routers:
You
simply need to draw, control the tool path and finally move the
machine with the generated G-codes.
Usable
software:
-ConstruCAM-3D - WIN PCNC- Mach2/Mach 3 -
to 3D- CNC router / milling and engraving machine / engraver
-DeskProto - WIN PCNC- Mach2/Mach 3 - to 3D- CNC router / milling
and engraving machine
fresadora fresatrice fraiseuse Jyrsintae
fraisage machin Freesmachine Frezesanas masina frezavimo masinos ?
Frezarka Freza Fraesmaskin Frézovací stroj Frézka ?; New ready for
operation
seller offer No. resale 67805462
|