| Description: |
glue aplication machine BURKLE RB
used machine
2010 Burkle RB
A glue application machine purchased in 2010
The machine can either be resold or serve as a spare parts donor
Space requirement: approx. 16x7.0m
Connected loads: Nominal power 20Kw
Main components: Heavy-duty chain conveyor, roller conveyor
Gantry unit with vacuum pump
Glue application rollers
ALTEK lifting table type AEA-30.12
Machine list
Basic equipment
Item 10 Heavy-duty chain conveyor
Item 20 Portal stacker
Item 30 Roller conveyor with centring unit
Item 40 Roller conveyor
Item 50 Roller applicator
Item 60 Platform for roller applicator
Item 70 Roller conveyor
Item 80 Angle transfer
Item 90 Scissor lift
Item 100 Working platform application area, manually adjustable
Item 110 Glue feed
Item 10 Heavy-duty chain conveyor
Item 10 Heavy-duty chain conveyor
For pallet feed
A welded frame made of rectangular steel bars with height-adjustable
feet. Three chain conveyor arms are fitted for transverse
transport.
The pallets are automatically positioned under the stacker.
Length: approx. 3500 mm
Width: approx. 2500 mm
Height: 300 ± 20 mm
Item 20 Portal stacker
Technical description:
The straddle stacker has a stable steel construction. The two
collection gates are
are constructed from rectangular steel rods. A horizontal drive device
consisting of a steel rod is mounted on these openings.
The drive carriage runs horizontally on rollers on this rod.
A vertical lifting mechanism with an attached suction frame is
installed underneath the trolley. The vacuum is generated by a side
channel blower mounted on the carriage. The vacuum is channelled
through pipes to the lower end of the lifting mechanism and
distributed to the suction frames. Frequency-controlled drive set for
horizontal and vertical movement.
Technical data:
Length: approx. 4,700 mm
Number of loading positions: 1
Number of stacking positions: 1
Stacking height: max. 1200 mm incl. pallet
Capacity: approx. 4 pcs. per minute (approx. possible capacity)
Item 30 Roller conveyor with centring unit
Technical description:
The basic construction of the roller conveyor consists of a rigid
welded frame of rectangular steel bars with adjustable feet.
The sprockets are rotated by a chain that is driven tangentially
driven tangentially by a manual motor with variable speed, which is
located in the lower
located in the lower section of the base structure. The guide chain
runs in plastic slide rails over the entire length of the roller
conveyor. The chains can be tensioned using adjusting screws on the
motor attachment. The tangential chain drives of the motors are
completely covered by protective covers.
The roller conveyor is also equipped with a pneumatically operated
centring device.
Technical data
Length: approx. 3250 mm
Width: approx. 1500 mm
Height: approx. 1500 (- 30 / + 70) mm
Roller pitch: approx. 300 mm
Item 40 Roller conveyor
Technical description:
The basic construction of the roller conveyor consists of a rigid
welded frame of rectangular steel bars with adjustable feet.
The chain wheels are rotated by a chain that is driven tangentially by
a
driven tangentially by a manual motor with variable speed, which is
located in the lower
located in the lower section of the base structure. The guide chain
runs in plastic slide rails over the entire length of the roller
conveyor. The chains can be tensioned using adjusting screws on the
motor attachment. The tangential chain drives of the motors are
completely covered by protective covers.
The roller conveyor is also equipped with a pneumatically operated
centring device.
Technical data
Length: approx. 3250 mm
Width: approx. 1500 mm
Height: approx. 1500 (- 30 / + 70) mm
Roller pitch: approx. 300 mm
Item 50 Roller applicator
For one-sided application of liquid adhesives to flat workpieces.
Application unit
- Separate, single-rotating direct drive for the application
roller.
- Rubber-covered applicator roller with grooved rings for pressureless
end plates.
- Quick-change coupling for the application roller with spherical
bearings and a chain coupling.
- Separate, single-rotating direct drive for the doctor roller, high
differential speed to the application roller (1:20).
- Hard rubber squeegee roller with grooved rings for pressureless end
plates;
with a sensitive squeegee roller adjustment system that can be mounted
via a worm gear, rollers
Adjustment of the roller gap on the mechanical digital display on the
handwheel, display accuracy 0.1 mm.
- Parallelism of the rollers can be adjusted using a sliding
clutch.
- Splash-proof bearing.
- Easy to open bonnet.
Height adjustment
- Precision lifting gear, hard chrome-plated round columns for
guidance, operated by a handwheel.
handwheel.
- Mechanical digital display of throughput height, display accuracy
0.1 mm.
- High pressure of the pressure roller on the workpiece.
Machine frame
- Solid frame construction.
- Good accessibility for maintenance / cleaning
- Integrated pull-out cleaning tray
Item 60 Platform for roller applicator
Switching for cleaning
The applicator and squeegee roller rotates even when the protective
bonnet is open if the height adjustment and squeegee roller adjustment
are set to the safety distance. The safety distances are sensed
electrically by a limit switch. Electrical equipment:
- In accordance with DIN/VDE (EN60204-1).
- Operating elements in an ergonomically arranged control panel.
Cable connection machine/control cabinet
- Control system in a separate control cabinet (800 x 1,400 x 300
mm)
- The control cabinet next to the machine is connected to the machine
frame on the travelling side, on the drive side.
Technical data
Working width 1,300 mm
1 rubber-covered application roller with a diameter of Æ 240 mm
Hardness of the rubber coating 70 Shore
Grooving 20 grooves/"
Width of the application roller 1,416 mm
1 squeegee roller with hard rubber cover with a diameter of Æ 185
mm
Hardness of the rubber cover 85 Shore
Width of the squeegee roller 1,416 mm
Maximum throughput height 120 mm
Length of the machine approx. 1200 mm
Working height 870 +/-50 mm
Weight approx. 1,250 kg
Operating voltage 400/50 V/cycles
Connected load at 50 cycles approx. 3 kW
Speed of the application roller 6 - 40 m/min.
Speed of squeegee roller 1 - 6 m/min.
Additional equipment:
1.0 feed speed, frequency-controlled:
Machine design as described above with the following changes:
- Speed of the transport and application roller 6 - 40 m/min.
- Speed of the doctor roller 1 - 6 m/min.
- Connected load at 50 cycles approx. 3.8 kW
2.0 Motorised height adjustment with push button
Offer no. 80973D - Page 13 of 31 - 09.06.2010
3.0 Retractable design for cleaning the machine. Special
undercarriage
Chassis including rails under the machine with additional plastic
wheels
plastic wheels for a rail-free working area. Including two position
monitoring switches for bypassing line controls.
4.0 Height sensing of the roller gap
4.4 Spray pipes for cleaning with flat jet nozzles (min. water
pressure 3 bar)
5.0 Special rubber coating of the application roller
5.1 Special grooving of the application roller
6.1 Machine base for working heights above 1100 mm
9.0 Transport system with 3 driven rollers on the infeed side (D=70
mm)
Min. part length: 350 U41158834 mm
Length of the machine: 1,200 mm
9.1 Transport system with 3 driven rollers on the outfeed side (D=70
mm)
Min. part length: 350 mm
Length of the machine: 1,200 mm
10.0 Machine as described in the previous text with the following
additional equipment: Application unit at the bottom is omitted
(one-sided glue application from above)
11.0 Throughput height up to 200 mm
Item 70 Roller conveyor
Technical description:
The basic construction of the roller conveyor consists of a rigid
welded frame made of rectangular steel bars with adjustable feet. The
chain wheels are rotated by a chain that is driven tangentially by a
manual motor with variable speed, which is located in the lower
section of the basic structure. The guide chain runs in plastic slide
rails over the entire length of the roller conveyor. The chains can be
tensioned using adjusting screws on the motor mounting. The tangential
chain drives of the motors are completely covered by
completely covered by protective covers.
Technical data:
Length: approx. 3250 mm
Width: approx. 1500 mm
Height: approx. 1500 (- 30 / + 70) mm
Roller pitch: approx. 300 mm
Item 80 Angle transfer
Technical description:
The basic construction of the roller conveyor with angled transfer
consists of a rigid
welded frame made of rectangular steel bars with adjustable feet for a
variable infeed, infeed height of +75/-25 mm.
- Transport rollers with steel cover, galvanised.
- The chain is driven by a frequency-controlled geared motor.
- The chain can be tensioned by adjusting screws on the motor
attachment.
- Swivelling toothed belt conveyor arms mounted on the underside for
angular transfer.
- Chain drive by motor with variable speed
Length: 3250 mm
Width: 1600 mm
Item 90 Scissor lift
For manual loading / stacking of the above-mentioned material types
- Scissor lift table, with integrated hydraulic unit
- Hydraulic unit, mounted outside the frame of the scissor lift
- Lifting table with integrated safety system (safety edge)
- The lift table is levelled using a foot switch
Dimensions of the lift table, approx.: 2000 x 1400 mm
Lifting height of the table, approx.: 1200 mm
Max. Stacking height: 1200 mm incl. pallet
Height of the construction, approx.: 360 mm
Max. Stacking weight: 3 tonnes
Lifting speed: 50 mm/s
Additional equipment: Platform extensions to increase the length
Item 100 Working platform support area, manually adjustable
Technical description:
- 2 working platforms for an ergonomic working position at the manual
laying station.
- Manually adjustable to the individual part length to be produced
Platform height: approx. 500 - 700 mm
Pos. 110 Glue supply
Single-circuit system that can be used with either Racoll GXL3 or
Latyl ST52
Consisting of:
- Frame for IBC glue tanks
- Glue tanks are provided on site by the customer
- Hosing/piping
- valves
- Filter for Racol
- Agitator
- Plastic tank for Racoll GXL3, capacity approx. 200 litres
- Membrane transfer pump 1" made of PP plastic
- Switch cabinet
- Quick-release couplings for tank connection
Find more here - /
Contact us at -
seller offer No. resale 5361560
|