| Description: |
Injection molding machines ARBURG 420C 1000-150/150/60 -3-Farben
used machine
Injection moulding machine 3-colours
(horizontal /vertical/ and 3rd in L-position with protective
enclosure)
with turntable
available now from our warehouse Hannover
Make: Arburg
Type: 420C 1000-150/150/60
Built in 2003
Control: Selogica
Hours: 20092 h
+Closing Unit+
Clamping force: 1000 kN / 1000 to.
Tie bar ratio: 420 x 420 mm
Plate size: 570 x 570 mm
Injection Unit 1 (150 unit)
Screw size: 15 mm (high-screw)
Pvlzwy
Spray volume: 17 cc
Spray weight: 15 gr.
Spray pressure: 2750 bar
Injection Unit 2 (150 unit
Screw size: 15 mm (high-screw)
Spray volume: 17 cc
Spray weight: 15 gr.
Spray pressure: 2750 bar
Injection Unit 3 (60 unit)
Screw size: 15 mm (high-screw)
Spray volume: 17 cc
Spray weight: 15 gr.
Spray pressure: 2080 bar
extras
1 ALLROUNDER 420 C 1000 - 150 / 150 / 60 fully hydraulic screw
injection moulding machine
Tool clamping force 1000 kN Voltage 400 V / 50 Hz
1 Vertical injection unit instead of on the locking bars mounted on
beams for 2nd injection unit, hand-operated, working position movable
bar between 70 and 250 mm VE-404/02
1 Open nozzle 15 mm low-wear, without heating tape (1.SPE 150)
VE-902/00
1 Technology level 2 - servo-controlled hydraulic system with two
control pumps for controlled machine movements, with away-dependent,
controlled target ramps. The structure of the tool holding force is
programmable and regulated. The holding force is held servo-controlled
via the second pump. The structure of the nozzle system force is
programmable. The investment force is manually adjustable, the value
is controlled. This technology level is a pre-ecipium for simultaneous
movements of nozzle, ejector and optional core trains. Including
equipment package for "Advanced Driving Movements". VE-132/03
1 Technology stage 3 hydraulic system with 3 control pumps for
simultaneous movements of the main axes and for faster movements of
the secondary axes. For the 2-K machines as hydraulic system for the
2nd injection unit (prerequisite is technology level 2, VE 132/03)
VE-130/40
1 heating belt for open nozzle VE-320/00
1 Injection unit 150 for vertical injection into the tool separation
during 2-K processing VE-136/02
1 Position-controlled screw with control valve on the injection unit,
incl. controlled pressure, nozzle system force manually adjustable
VE-561/20
1 Position-controlled screw with control valve for multi-component
machines incl. controlled storage pressure, nozzle system force
manually adjustable - for injection unit 2 VE-561/30
1 Injection unit 60 for horizontal injection into the tool separation
as 3rd injection unit for multi-component processing (L-position)
VE-906/00
1 to VE 906/00 Injection unit 60 in L-position: unit lowered by 70 mm,
incl. special separation plane and full protection VE-907/00
1 plasticizing cylinder set 15 mm (without nozzle), with pre-loaded
feed and pressure reducing valve, in high-wear-resistant version with
sinter-metal backflow lock, i.e. highly wear- and corrosion-resistant
for processing thermoplastics with highly abrasive or corrosive
components and for high-temperature materials (L-position) VE-908/00
1 Open nozzle 15 mm low-wear, without heating tape (L-position)
VE-909/00
1 nozzle tip with radius 15 (L-position) VE-910/00
1 heating belt for open nozzle (L-position) VE-911/00
1 Position-controlled screw for the third injection unit for 3-K
machines, with control valve on the injection unit, controlled storage
pressure and manually adjustable with nozzle system force
(prerequisite is technology level 2) VE-918/00
1 Control extension for repressurization via hydraulic pressure
VE-471/01
1 Electrical connection for pneumatic needle enclosing nozzle in the
VE-317/00 tool
1 Electrical connection for pneumatic needle closing nozzle in the
tool for third injection unit VE-913/00
1 to VE 317/00 and 913/00 "pneum. NVD in WKZ": 1 pneum. Control for
nozzles in the mech tool. + electr.) includes 2 x 5/3 way valve incl.
respective pressure setting; Attachment to mesh back, at the height of
the fixed WKZ plate (as with machine 185.801) VE-914/00
1 Clamping plate set 420 with central injection position and centering
diameter 125 mm VE-356/11
1 to VE 356/11 Clamping plate set: special bores in lelet. WKZ plate -
for ejectors: 4x D35 H7 on hor. + vert. Center axis distance 100 mm
each, standard. Ejector holes (distance 85 mm) remain -for guide
ejector cross: holes offset from the center axis to the right (see
sketch) VE-921/00
1 Extension of the locking bars to the corresponding increase of the
minimum tool installation height to 350 mm, the opening path (stroke)
remains unchanged, the lateral protective enclosure must be increased
according to the safety level (VE 389/01), the tool closing area
remains open upwards VE-357/35
1 Machine-related cooling circuits programmable VE-525/02
1 to VE 525/02 "mash. in z. cooling circuits": Cooling circuits with
measuring tube VE-916/00
1 Basic equipment for additional cooling water distributors with
separate inlet and outlet, hand-adjustable, with measuring tube for
S41224506 this purpose: VE-514/00
1 - 5 free cooling circuits, connection DN 13 VE-514/05
1 1. Core pull control for simultaneous movements, the holding
pressure is hand-adjustable - in the case of serial movements pressure
and flow are programmable - at the simultaneous movements the pressure
is hand-adjustable, the flow is load-dependent connections on movable
tool plate, in machines with vertical clamping unit on the hydraulic
block; the hydraulic cylinders and hoses are not included VE-382/02
1 Extension for the hydraulic rotary control to drive the ARBURG
rotary unit, controlled, with brake ramps and programmable speeds
VE-382/08
1 Hydraulically driven 3-station rotary unit for multi-component tools
for attachment to the movable tool clamping plate, rotational movement
120 degrees or 180 degrees continuous, incl. adjustment, with 4
cooling circuits, ejector position at the bottom or rear, delivery is
carried out with additional parts such as hydraulic hoses and limit
switch VE-919/00
1 to VE 919 Rotary unit: in special version for ejecting in sub-circle
200, ejector possibility in upper or operating. (90°) Cavity, booked
for ejector bolts D 24 VE-920/00
1 2. Core pull control for simultaneous movements, the holding
pressure is programmable - in the serial movements pressure and flow
are programmable - at the simultaneous movements the pressure is
programmable, the flow is load-dependent connections on movable tool
plate, in machines with vertical clamping unit on the hydraulic block;
the hydraulic cylinders and hoses are not included in the scope of
delivery (can be used in the S-series from T-2, in the C-series from
T-2 servo-controlled) VE-382/13
1 to VE 382/13 Core pull control: core pull incl. twin check valve
VE-912/00
1 ausw
1 to VE 572/00 Ejector Cross. in special version, adapted to movable
WKZ plate, possibility to eject to 85 mm and 100 mm distance (upper or
operating. (90°) cavity) incl. adapted shell coupling (without
ejector bolt) VE-922/00
Etc.
fully functional cross for extra-middle ejection, in combination with
2-K rotation units, for max. 3 ejector bolts incl. 1 shell coupling,
usable VE-572/00
seller offer No. resale 152660693
|